Driveline transfer: TY21B

Transfer case

In this manual: Driveline transfer: TY21B
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~5min read

Exploded View

1. Pinion lock nut

1. Pinion lock nut
2. Companion flange
3. Drive pion oil seal
4. Pinon rear bearing
5. Transfer case
6. Gasket
7. Filler plug
8. Collapsible spacer
9. Drive pinion adjust shim 10. Drive pinion
11. Pinion front bearing 12. Ring gear
13. Ring gear shaft
14. Ring gear bearing (right) 15. Ring gear bearing adjust shim (right) 16. Spacer (right)
17. Transfer case oil seal (right) 18. Drive shaft oil seal 19. Transfer cover
20. Oil defense
21. Ring gear bearing (left) 22. Ring gear bearing adjust shim (left) 23. Spacer (left)
24. Transfer case oil seal (left) 25. Drain plug
26. Dowel pin

A. Oil seal lip
B. Transfer case mounting face

: Always replace after every: N·m (kg-m, ft-lb)
disassembly.: Always replace after every
disassembly. : Apply anti-corrosive oil.: Apply gear oil.
: Apply multi purpose grease: Apply anti-corrosive oil.
: Apply Genuine Liquid Gasket 1215: Apply multi purpose grease
or equivalent.: Apply Genuine Liquid Gasket 1215
or equivalent.

Disassembly: Select with proper thickness.


Disassembly

1. Remove transfer cover mounting bolts. 2. Lightly tap (A) position of transfer cover with a plastic hammer to remove transfer cover.

3. Remove ring gear shaft assembly. Refer to DLN-96, "Disassembly",

4. Tap the outer race of drive pinion bearing from transfer case with

4. Tap the outer race of drive pinion bearing from transfer case with a brass rod to remove outer race of drive pinion bearing (front side and rear side).

CAUTION:
Never damage transfer case.

5. Remove dowel pin.

CAUTION:
Never remove dowel pin, if it is not necessary to replace.
6. Remove the filler plug and drain plug from the transfer case, and then remove each gasket. 7. Remove oil defense from transfer cover.

8. Perform inspection after disassembly. Refer to DLN-116, "Inspection".

Assembly

Assembly

1. Install the oil defense to transfer cover.

2. Install gaskets onto filler plug and drain plug and install them into transfer case.

CAUTION:
• Never reuse gaskets.

• Install filler plug after oil is filled.

3. Install the dowel pin to transfer case.

CAUTION:
Never reuse the dowel pin.

4. Install outer race of drive pinion bearing (front side) to the transfer case with drift (A) (SST: ST17130000).

CAUTION:
• Never reuse drive pinion bearing (front side).

• Apply gear oil to the drive pinion bearing (front side)

5. Install outer race of drive pinion bearing (rear side) to transfer

5. Install outer race of drive pinion bearing (rear side) to transfer case with a drift (A) (SST: ST33230000).

CAUTION:
• Never reuse drive pinion bearing (rear side).

• Apply gear oil to the drive pinion bearing (rear side).

6. Install drive pinion assembly to transfer case. Refer to DLN-110, "Assembly".

7. Install ring gear shaft assembly to transfer case. Refer to DLN- 97, "Assembly".

8. Set the drifts (A and B) to right and left side spacers individually.

8. Set the drifts (A and B) to right and left side spacers individually.

Compress ring gear shaft assembly and ring gear bearing to install transfer cover to transfer case.

A : Drift (commercial service tool) B : Drift (commercial service tool)

CAUTION:
• Clean the mounting surface of transfer case and transfer cover to degrease sufficiently. • Never apply gasket fluid on the mounting surface. • The drift shall be placed on the center of the spacers. • The pressure shall be as low as to install ring gear shaft assembly into transfer case. The maximum pressure shall be 10 kN (1 ton, 1.0 Imp ton).

• If the adjusting shims and spacers are installed by tapping, the transfer cover may be damaged.

Avoid tapping.

9. Check backlash, tooth contact, total preload and companion flange runout.

9. Check backlash, tooth contact, total preload and companion flange runout. Refer to DLN-98, "Adjustment".

CAUTION:
Measure the total preload without the transfer case oil seals.
10. Remove transfer cover. Refer to DLN-114, "Disassembly".

11. Apply liquid gasket (1) to mating surface of rear cover.

Also remove any moisture, oil, or foreign material adhering to the mounting surfaces. • Overlap both ends of the bead for at least 3 mm (0.12 in).
12. Set the drifts (A and B) to right and left side spacers individually.

12. Set the drifts (A and B) to right and left side spacers individually.

Compress ring gear shaft assembly and ring gear bearing to install transfer cover to transfer case.

A : Drift (commercial service tool) B : Drift (commercial service tool)

CAUTION:
• Immediately install after applying gasket. • The drift shall be placed on the center of the spacers. • The pressure shall be as low as to install ring gear shaft assembly into transfer case. The maximum pressure shall be 10 kN (1 ton, 1.0 Imp ton).

• If the adjusting shims and spacers are installed by tapping, the transfer cover may be damaged.

Avoid tapping.

13. Tighten rear cover mounting bolts to the specified torque.

13. Tighten rear cover mounting bolts to the specified torque.

14. Install transfer case oil seal (right side) until it becomes flush with ring gear shaft end, using the drifts (A and B).

A : Drift (SST: ST30720000) B : Drift (SST: ST19820000)

CAUTION:
• Never reuse oil seals. • When installing, do not incline oil seals. • Apply multi-purpose grease onto oil seal lips, and gear oil onto the circumference of oil seal.

• Immediately install after installing transfer cover.

15. Install transfer case oil seal (left side) until it becomes flush with

15. Install transfer case oil seal (left side) until it becomes flush with ring gear shaft end, using the drift (A) (SST: KV40100620).

CAUTION:
• Never reuse oil seals. • When installing, do not incline oil seals. • Apply multi-purpose grease onto oil seal lips, and gear oil onto the circumference of oil seal. • Immediately install after installing transfer cover.

• After installing oil seal, immediately wipe out gasket squeezed out inward of transfer case.

Inspection

Inspection

INSPECTION AFTER DISASSEMBLY

Check items below. If necessary, replace them with new ones.

Case
Check the bearing mounting surface for wear, cracks and damages.

CAUTION:
Replace transfer case and transfer cover as a set if any malfunction is detected on transfer case or transfer cover.