Engine Control System HR16DE

Fuel pressure check

In this manual: Engine Control System HR16DE
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~4min read
010203040501.51N·mlb·ft
Tightening torque found on this page
Work Procedure

FUEL PRESSURE RELEASE

1.FUEL PRESSURE RELEASE

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON. 2. Perform “FUEL PRESSURE RELEASE” in “WORK SUPPORT” mode with CONSULT-III. 3. Start engine. 4. After engine stalls, crank it two or three times to release all fuel pressure.

5. Turn ignition switch OFF.

1. Remove fuel pump fuse located in IPDM E/R.Without CONSULT-III


1. Remove fuel pump fuse located in IPDM E/R. 2. Start engine. 3. After engine stalls, crank it two or three times to release all fuel pressure. 4. Turn ignition switch OFF.

5. Reinstall fuel pump fuse after servicing fuel system.

>> INSPECTION END

FUEL PRESSURE CHECK

1.FUEL PRESSURE CHECK CAUTION:
• Before disconnecting fuel line, release fuel pressure from fuel line to eliminate danger. • The fuel hose connection method used when taking fuel pressure check must not be used for other purposes. • Be careful not to scratch or put debris around connection area when servicing, so that the quick connector maintains seal ability with O-rings inside.

• Do not perform fuel pressure check with electrical systems operating (i.e. lights, rear defogger, A/C, etc.) Fuel pressure gauge may indicate false readings due to varying engine load and changes in manifold vacuum.

NOTE:

Prepare pans or saucers under the disconnected fuel line because the fuel may spill out. The fuel pressure cannot be completely released because F15 models do not have fuel return system.

1. Release fuel pressure to zero.

2. Prepare fuel hose for fuel pressure check (B) and fuel tube adapter [SST (KV10118400) or (KV10120000)] (D), then connect fuel pressure gauge (A).

connector To quick
connector
tube (engine side) To fuel
tube (engine side)
C : Hose clamp

CAUTION:

CAUTION:
• Use suitable fuel hose for fuel pressure check (genuine NISSAN fuel hose without quick connector). • To avoid unnecessary force or tension to hose, use moderately long fuel hose for fuel pressure check. • Do not use the fuel hose for checking fuel pressure with damage or cracks on it.

• Use Pressure Gauge to check fuel pressure.

3. Remove fuel hose.

CAUTION:
Do not twist or kink fuel hose because it is plastic hose.

4. Connect fuel hose for fuel pressure check (1) to fuel tube (engine side) with clamp (2) as shown in the figure.

5 : No.2 spool

CAUTION:

CAUTION:
• Wipe off oil or dirt from hose insertion part using cloth moistened with gasoline. • Apply proper amount of gasoline between top of the fuel tube (3) and No.1 spool (4). • Insert fuel hose for fuel pressure check until it touches the No.1 spool on fuel tube. • Use NISSAN genuine hose clamp (part number: 16439 N4710 or 16439 40U00). • When reconnecting fuel line, always use new clamps. • Use a torque driver to tighten clamps.

• Install hose clamp to the position within 1 - 2 mm (0.04 - 0.08 in).

Tightening torque : 1 - 1,5 N·m

• Make sure that clamp screw does not contact adjacent parts.

5. Connect fuel tube adapter to quick connector (1).

A : Fuel pressure gauge

6. After connecting fuel hose for fuel pressure check, pull the hose with a force of approximately 98 N (10 kg, 22 lb) to confirm fuel tube does not come off. 7. Turn ignition switch ON and check for fuel leakage. 8. Start engine and check for fuel leakage.

9. Read the indication of fuel pressure gauge.

Fuel pressure gauge may indicate false readings. • During fuel pressure check, confirm for fuel leakage from fuel connection every 3 minutes.
At idling : Approximately 350 kPa (3.5 bar, 3.57 kg/cm2, 51 psi)

At idling : Approximately 350 kPa (3.5 bar, 3.57 kg/cm2, 51 psi)

Is the inspection result normal? YES >> INSPECTION END

NO >> GO TO 2.

2.CHECK FUEL HOSE AND FUEL TUBE

If result is unsatisfactory, check fuel hoses and fuel tubes for clogging.

Is the inspection result normal? YES >> Replace “fuel filter and fuel pump assembly”.

NO >> Repair or replace.