Engine Control System HR16DE

Idle air volume learning

In this manual: Engine Control System HR16DE
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~4min read

Description

Idle Air Volume Learning is a function of ECM to learn the idle air volume that keeps each engine idle speed within the specific range. It must be performed under any of the following conditions:
• Each time electric throttle control actuator or ECM is replaced.

• Idle speed or ignition timing is out of specification.

Work Procedure

1.PRECONDITIONING

Make sure that all of the following conditions are satisfied.

Learning will be cancelled if any of the following conditions are missed for even a moment.

• Battery voltage: More than 12.9 V (At idle) • Engine coolant temperature: 70 - 100 °C • Selector lever: P or N (CVT), Neutral (M/T) • Electric load switch: OFF (Air conditioner, headlamp, rear window defogger) - For vehicles equipped with daytime light systems, perform one of the following procedures before starting engine not to illuminate headlamps.

• Apply parking brake
• Set lighting switch to the 1st position • Steering wheel: Neutral (Straight-ahead position) position • Vehicle speed: Stopped • Transmission: Warmed-up - CVT models

• With CONSULT-III: Drive vehicle until “FLUID TEMP SE” in “DATA MONITOR” mode of “TRANSMISSION” system indicates less than 0.9 V. • Without CONSULT-III: Drive vehicle for 10 minutes.

- M/T models

• Drive vehicle for 10 minutes.

Do you have CONSULT-III? YES >> GO TO 2.

NO >> GO TO 3.

2.IDLE AIR VOLUME LEARNING

1. Perform ACCELERATOR PEDAL RELEASED POSITION LEARNING. Refer to EC-542,With CONSULT-III


1. Perform ACCELERATOR PEDAL RELEASED POSITION LEARNING. Refer to EC-542, "Work Procedure". 2. Perform THROTTLE VALVE CLOSED POSITION LEARNING. Refer to EC-543, "Work Procedure". 3. Start engine and warm it up to normal operating temperature. 4. Select “IDLE AIR VOL LEARN” in “WORK SUPPORT” mode with CONSULT-III.

5. Touch “START” and wait 20 seconds.

Is “CMPLT” displayed on CONSULT-III screen? YES >> GO TO 4.

NO >> GO TO 5.

3.IDLE AIR VOLUME LEARNING

NOTE:Without CONSULT-III


NOTE:
• It is better to count the time accurately with a clock.

• It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit has a malfunction.

1. Perform ACCELERATOR PEDAL RELEASED POSITION LEARNING. Refer to EC-542, "Work Procedure". 2. Perform THROTTLE VALVE CLOSED POSITION LEARNING. Refer to EC-543, "Work Procedure". 3. Start engine and warm it up to normal operating temperature. 4. Turn ignition switch OFF and wait at least 10 seconds. 5. Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.

6. Repeat the following procedure quickly five times within 5 seconds.

- Fully depress the accelerator pedal.

- Fully release the accelerator pedal.

7. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MI stops blinking and turned ON. 8. Fully release the accelerator pedal within 3 seconds after the MI turned ON. 9. Start engine and let it idle.

10. Wait 20 seconds.

>> GO TO 4.

4.CHECK IDLE SPEED AND IGNITION TIMING

Rev up the engine two or three times and make sure that idle speed and ignition timing are within the specifications.

For specification, refer to EC-807, "Idle Speed" and EC-807, "Ignition Timing".

Is the inspection result normal? YES >> INSPECTION END

NO >> GO TO 5.

5.DETECT MALFUNCTIONING PART Check the following
• Check that throttle valve is fully closed. • Check PCV valve operation.

• Check that downstream of throttle valve is free from air leakage.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace malfunctioning part.

6.DETECT MALFUNCTIONING PART

Engine component parts and their installation condition are questionable. Check and eliminate the cause of the incident.

It is useful to perform “TROUBLE DIAGNOSIS - SPECIFICATION VALUE”. Refer to EC-558, "Description".

If any of the following conditions occur after the engine has started, eliminate the cause of the incident and perform Idle Air Volume Learning all over again: • Engine stalls.

• Erroneous idle.

>> INSPECTION END

Mixture ratio self-learning value clear