Restraints

B0001 Driver Air Bag Module

25steps
~150min
5/5difficulty
Done 0 of 25
DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detecting condition
B0001-1A

DRIVER AIRBAG MODULE

[SHORT]
Diagnosis condition When ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 32 and 33)
Threshold —
Diagnosis delay time —
B0001-13

DRIVER AIRBAG MODULE

[OPEN]
Diagnosis condition When ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 32 and 33)
Threshold —
Diagnosis delay time —
B0001-12

DRIVER AIRBAG MODULE

[VB-SHORT]
Diagnosis condition When ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 32 and 33)
Threshold —
Diagnosis delay time —
B0001-11

DRIVER AIRBAG MODULE

[GND-SHORT]
Diagnosis condition When ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 32 and 33)
Threshold —
Diagnosis delay time —
B0001-09

DRIVER AIRBAG MODULE

[SHORT]
Diagnosis condition When ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 32 and 33)
Threshold —
Diagnosis delay time —
B0001-00

DRIVER AIRBAG MODULE

[SHORT]
Diagnosis condition When ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 32 and 33)
Threshold —
Diagnosis delay time —

POSSIBLE CAUSE

[OPEN]

  • Connection malfunction or open circuit of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

[VB-SHORT]

  • Connection malfunction or short circuit to power supply of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

[GND-SHORT]

  • Connection malfunction or short circuit to ground of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

[SHORT]

  • Connection malfunction or short circuit of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch ON.

  2. Select "Self Diagnostic Result" mode of "AIR BAG".

  3. Check for DTC.

Is the DTC detected?

YES>>

(Current DTC) Refer to DTC Diagnosis Procedure.

YES>>

(Past DTC) GO TO 2.

NO>>

Inspection End.

ERASE SELF DIAGNOSTIC RESULT

CONSULT

Erase the DTC.

Can the DTC be erased?

YES>>

Inspection End.

NO>>

Refer to DTC Diagnosis Procedure.

DTC CONFIRMATION PROCEDURE

CHECK SELF DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch ON.

  2. Check the air bag warning lamp status. Refer to SRS Operation Check.

Is the DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal

  • Loose terminal

  • Poor connection

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform one of the following repairs:

  • Visible damage: Replace the harness.

  • Loose terminal: Secure the terminal.

  • Poor connection: Secure the connection.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Select "Self Diagnostic Result" mode of "AIR BAG".

  4. Check for DTC.

Is DTC still current?

YES>>

GO TO 3.

NO>>

Refer to Intermittent Incident.

WIRING HARNESS

Check the wiring harness for visible damage.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace the harness.

CHECK SPIRAL CABLE CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect driver air bag module harness connector and combination switch (spiral cable) harness connector.

  3. Check continuity between driver air bag module harness connector and combination switch (spiral cable) harness connector.

    Driver air bag moduleCombination switch (spiral cable)Continuity
    ConnectorTerminalConnectorTerminal
    M76 29 M41 22 Yes
    30 24
  4. Check continuity between driver air bag module harness connector and ground.

    Driver air bag module—Continuity
    ConnectorTerminal
    M76 29 Ground No
    30

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace the spiral cable. Refer to Removal and Installation.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Select "Self Diagnostic Result" mode of "AIR BAG".

  4. Check for DTC.

Is DTC still current?

YES>>

GO TO 6.

NO>>

Refer to Intermittent Incident.

DRIVER AIR BAG MODULE

CONSULT

  1. Replace the driver air bag module. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Select "Self Diagnostic Result" mode of "AIR BAG".

  4. Check for DTC.

Is DTC still current?

YES>>

GO TO 7.

NO>>

Clear DTC. Inspection End.

AIR BAG DIAGNOSIS SENSOR UNIT

CONSULT

  1. Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Select "Self Diagnostic Result" mode of "AIR BAG".

  4. Check for DTC.

Is DTC still current?

YES>>

GO TO 8.

NO>>

Clear DTC. Inspection End.

RELATED HARNESS

Replace the related harness.

>>

Inspection End.