Transmission & Driveline

Ecu Diagnosis Information. Awd Control Unit

6steps
~36min
4/5difficulty
Done 0 of 6
Values on the Diagnosis Tool
Monitor itemConditionValue/Status
STOP LAMP SW Brake pedal: Depressed On
Brake pedal: Released Off
ENG SPEED SIG

Engine stopped

(Engine speed: Less than 400 rpm)
Stop

Engine running

(Engine speed: 400 rpm or more)
Run
ETS ACTUATOR Engine stopped (Ignition switch: ON) Off
Engine running On
4WD WARN LAMP AWD warning icon/display: ON On
AWD warning icon/display: OFF Off
4WD MODE SW Always AUTO
4WD MODE MON Always AUTO
DIS-TIRE MONI Nissan Murano Vehicle running with normal size tire installed 0 – 4 mm
Nissan Murano Vehicle running with improper size tire installed (Front/rear tire size difference, wear condition) 4 – 8 mm, 8 – mm
P BRAKE SW Parking brake operated On
Parking brake not operated Off
BATTERY VOLT Always Battery voltage
THRTL POS SEN

When depressing accelerator pedal

(Value rises gradually in response to throttle position.)
0 – 100%
ETS SOLENOID

Engine running

  • At idle speed

Approx. 0.000 A

Engine running

  • 3,000 rpm or more constant

Approx. 0.000 – 1.800 A*
FR RH SENSOR Nissan Murano Vehicle stopped 0 km/h

Nissan Murano Vehicle running

Nearly matches the speed meter display (±10% or less)
FR LH SENSOR Nissan Murano Vehicle stopped 0 km/h

Nissan Murano Vehicle running

Nearly matches the speed meter display (±10% or less)
RR RH SENSOR Nissan Murano Vehicle stopped 0 km/h

Nissan Murano Vehicle running

Nearly matches the speed meter display (±10% or less)
RR LH SENSOR Nissan Murano Vehicle stopped 0 km/h

Nissan Murano Vehicle running

Nearly matches the speed meter display (±10%)
Unit characteristic 1 The unit characteristics 1 of electric controlled coupling is displayed. 0.32 Amps
Unit characteristic 2 The unit characteristics 2 of electric controlled coupling is displayed. 0.58 Amps
Unit characteristic 3 The unit characteristics 3 of electric controlled coupling is displayed. 0.91 Amps
Unit characteristic 4 The unit characteristics 4 of electric controlled coupling is displayed. 1.74 Amps
Unit characteristic 5 The unit characteristics 5 of electric controlled coupling is displayed. 2.23 Amps

*: The values are changed by throttle opening and engine speed.

Reference Value

TERMINAL LAYOUT

PHYSICAL VALUES

Terminal No.

(Wire color)
DescriptionConditionValue (Approx.)
+-Signal nameInput/Output

1

(G/W)
Ground AWD solenoid power supply Output Engine speed: At idle 0 V
Engine speed: 3,000 rpm or more constant 2.5 V*

2

(Y)
Ground AWD solenoid ground Input Always 0 V

7

(W/O)
Ground Ignition switch Input Ignition switch: ON Battery voltage
Ignition switch: OFF 0 V

8

(L)
— CAN-High Input/Output — —

9

(L/W)
Ground Power supply (AWD solenoid) Input Always Battery voltage

10

(GR)
Ground Ground — Always 0 V

11

(GR)
Ground Ground — Always 0 V

15

(G)
Ground Power supply (AWD control unit) Input Always Battery voltage

16

(P)
— CAN-Low Input/Output — —

*: The values are changed by throttle opening and engine speed.

Fail-Safe
  • If any malfunction occurs in AWD electrical system, and control unit detects the malfunction, AWD warning icon/display on information display is displayed to indicate system malfunction.

  • When AWD warning icon/display is displayed, Nissan Murano vehicle changes to front-wheel drive or shifts to 4-wheel drive (rear-wheels still have some driving torque).

DTCAWD warning icon/displayPossible causeNissan Murano Vehicle condition
C1201
Internal malfunction of AWD control unit Front-wheel drive or shifts to 4-wheel drive (Rear-wheels still have some driving torque)
C1203

ABS malfunction

  • Nissan Murano Vehicle speed signal error

C1204
  • Internal malfunction of electronic controlled coupling

  • Malfunction of AWD solenoid power supply circuit (open or short)

  • Malfunction of AWD solenoid command current

C1205
  • Internal malfunction of AWD control unit

  • Malfunction of AWD solenoid power supply circuit (ground short)

C1210 Malfunction of engine control system
P1804 Internal malfunction of AWD control unit
P181F Writing unit characteristics is incomplete
U1000
  • CAN communication error

  • Internal malfunction of AWD control unit

U1010 Internal malfunction of AWD control unit
Protection Function

AWD system activates its protection function (shuts down AWD system temporarily) if AWD system detects high load continuously or the front wheel tire size differs from the rear tire size. (AWD system is automatically restored if AWD system no longer detects any overload or the tire size difference is eliminated.)

AWD warning icon/displayPossible causeNissan Murano Vehicle condition
(Displaying for approximately 1 minute and then turned OFF)

Drive train parts in protection mode. It is not malfunction.

(Internal temperature rise of electronic controlled coupling)

When this message is displayed, refer to Description.

Shuts down AWD system temporarily

(Front wheel drive)
(Continuing to display until ignition switch OFF)

Malfunction in each tire or different tire diameter

When this message is displayed, refer to Diagnosis Procedure.
DTC Inspection Priority Chart

If some DTCs are displayed at the same time, perform inspections one by one based on the following priority chart:

    • U1000 CAN COMM CIRCUIT

    • U1010 CONTROL UNIT(CAN)

    • C1201 CONTROLLER FAILURE

    • C1205 4WD ACTUATOR RLY

    • C1204 4WD SOLENOID

    • C1203 ABS SYSTEM

    • C1210 ENGINE SIGNAL 1

    • P1804 CONTROL UNIT

    • P181F INCOMP CALIBRATION

DTC Index
DTCDisplay ItemReference
C1201 CONTROLLER FAILURE DTC Description
C1203 ABS SYSTEM DTC Description
C1204 4WD SOLENOID DTC Description
C1205 4WD ACTUATOR RLY DTC Description
C1210 ENGINE SIGNAL 1 DTC Description
P1804 CONTROL UNIT DTC Description
P181F INCOMP CALIBRATION DTC Description
U1000 CAN COMM CIRCUIT DTC Description
U1010 CONTROL UNIT(CAN) DTC Description