Tilt And Telescopic Manual Switch
Components
COMPONENTS
ILLUSTRATION
*1 |
LOWER STEERING COLUMN COVER |
*2 |
TILT AND TELESCOPIC SWITCH |
*3 |
SPIRAL CABLE CONNECTOR |
- |
- |
Inspection
INSPECTION
PROCEDURE
1. INSPECT TILT AND TELESCOPIC SWITCH
(a) Remove the tilt and telescopic switch.
Click here ![]()
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the tilt and telescopic switch. |
|
Installation
INSTALLATION
PROCEDURE
1. INSTALL TILT AND TELESCOPIC SWITCH
(a) Engage the claw to install the tilt and telescopic switch.
(b) Connect the tilt and telescopic connector to the tilt and telescopic switch.
(c) Connect the spiral cable connector to the spiral cable sub-assembly.
2. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here ![]()
3. INSTALL LOWER STEERING COLUMN COVER
Click here ![]()
4. INSPECT SRS WARNING LIGHT
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
5. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during tilt and telescopic switch removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
PROCEDURE
1. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS
Click here ![]()
2. REMOVE LOWER STEERING COLUMN COVER
Click here ![]()
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here ![]()
4. REMOVE TILT AND TELESCOPIC SWITCH
(a) Disconnect the spiral cable connector from the spiral cable sub-assembly. |
|
(b) Disconnect the tilt and telescopic connector from the tilt and telescopic switch.
(c) Disengage the claw and pull out the tilt and telescopic switch.
*a |
Claw |
![]() |
Pull out in this direction |



