Removal
REMOVAL
PRECAUTION / NOTICE / HINT
The procedures required (adjustment, calibration, initialization or registration) that must be performed once parts have been removed, installed or replaced during side airbag sensor removal/installation are listed below.
Procedure Required After Replacing / Removing / Installing PartsReplacement part or procedure | Necessary Procedures | Effects / Inoperative Function When Necessary Procedure Not Performed | Link |
|---|---|---|---|
Disconnect the cable from the negative (-) battery terminal. |
Initialize Back Door Lock |
Door Lock Control System |
|
Memorize Steering Angle Neutral Point |
Lane Departure Alert System (with Steering Control) |
||
Pre-Collision System |
HINT:
- Repeat the same procedure for the right side and the left side.
- The following procedure applies to the left side.
PROCEDURE
1. PRECAUTIONS
CAUTION:
Be sure to read the Precautions carefully before performing maintenance.
Click here![]()
NOTICE:
After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.
Click here
![]()
2. DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL
Click here![]()
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
.png)
- If any Supplemental Restraint System (SRS) component is accidentally deployed, serious injury may result.
NOTICE:
When the cable has been disconnected, some systems must be reset after the cable is reconnected.
Click here
![]()
3. REMOVE SEAT BELT ANCHOR OUTER COVER
Click here![]()
4. DISCONNECT FRONT SEAT BELT OUTER BELT ASSEMBLY
Click here![]()
5. REMOVE FRONT DOOR SILL PLATE
Click here![]()
6. DISCONNECT FRONT DOOR SCUFF PLATE WEATHERSTRIP
HINT:
Disconnect the front door scuff plate weatherstrip so that the center pillar lower garnish can be removed.
7. REMOVE REAR DOOR SILL PLATE (with rear seat side airbag)
Click here![]()
8. REMOVE REAR DOOR SCUFF PLATE (without rear seat side airbag)
Click here![]()
9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
HINT:
Disconnect the rear door scuff plate weatherstrip so that the center pillar lower garnish can be removed.
10. REMOVE CENTER PILLAR LOWER GARNISH
Click here![]()
11. REMOVE NO. 1 SIDE AIRBAG SENSOR
(a) Make sure the ignition switch is in the OFF position.
(b) Make sure the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Remove the bolt and release the claw to detach the No. 1 side airbag sensor. |
![]() |
(d) Disconnect the connector to remove the No. 1 side airbag sensor.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
(1) Push the white housing lock and slide the yellow CPA. (At this stage, the connector cannot be disconnected.)
*a |
White housing lock |
*b |
Yellow CPA |
*c |
Slide |
*d |
Push in |
(2) Push the white housing lock again and disconnect the connector.
NOTICE:
Do not press the part (A) shown in the illustration when disconnecting the connector.
(e) After disconnecting the connector, make sure the white housing lock is in the position shown in the illustration.
*a |
Correct |
*b |
Incorrect |
12. REMOVE FLOOR SIDE AIRBAG SENSOR
(a) Make sure the ignition switch is in the OFF position.
(b) Make sure the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Remove the bolt and release the claw to detach the floor side airbag sensor. |
![]() |
(d) Disconnect the connector to remove the floor side airbag sensor.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
(1) Push the white housing lock and slide the yellow CPA. (At this stage, the connector cannot be disconnected.)
*a |
White housing lock |
*b |
Yellow CPA |
*c |
The connector is unlocked |
- |
- |
(2) Push the white housing lock again and disconnect the connector.
NOTICE:
Do not press the part (A) shown in the illustration when disconnecting the connector.
(e) Make sure that the position of the white case lock is the same as shown in the illustration.
*a |
Incorrect |
*b |
Correct |
.gif)
.png)
.png)