Supplemental Restraint Systems

Installation

~4min read
0102030405097N·mlb·ft
Tightening torque found on this page

INSTALLATION

PRECAUTION / NOTICE / HINT

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. INSTALL NO. 1 SIDE AIRBAG SENSOR

(a) Make sure the ignition switch is in the OFF position.

(b) Make sure the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Before connecting the connector, make sure the white housing lock is in the position shown in the illustration.

*a

Correct

*b

Incorrect

(d) Connect the connector to the No. 1 side airbag sensor.

*a

White housing lock

*b

Connect

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

HINT:

  • Be sure to connect the connector until it locks (when locking, make sure a click is heard).
  • When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or part (A), as this may cause improper connection.

(e) Engage the claw to install the No. 1 side airbag sensor with the bolt.

Torque:

9 N·m {92 kgf·cm, 80 in·lbf}

NOTICE:

  • If the No. 1 side airbag sensor has been dropped, or if the housing or connector shows cracks, nicks or other damage, replace it with a new one.
  • When installing the No. 1 side airbag sensor, make sure the SRS wiring does not interfere with or get pinched between other parts.
  • Make sure the claw of the No. 1 side airbag sensor is correctly inserted into the body hole.

(f) Make sure the installed No. 1 side airbag sensor parts are not loose.

2. INSTALL FLOOR SIDE AIRBAG SENSOR

(a) Make sure the ignition switch is in the OFF position.

(b) Make sure the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Connect the connector to the floor side airbag sensor.

*a

White housing lock

*b

The connection is complete.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

HINT:

  • Be sure to connect the connector until it locks (when locking, make sure a click is heard).
  • When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or part (A), as this may cause improper connection.

(d) Before connecting the connector, make sure the white housing lock position is as shown in the illustration.

*a

Incorrect

*b

Correct

(e) Engage the claw to install the floor side airbag sensor with the bolt.

Torque:

9 N·m {92 kgf·cm, 80 in·lbf}

NOTICE:

  • If the floor side airbag sensor has been dropped, or if the housing or connector shows cracks, nicks or other damage, replace it with a new one.
  • When installing the floor side airbag sensor, make sure the SRS wiring does not interfere with or get pinched between other parts.
  • Make sure the claw of the floor side airbag sensor is correctly inserted into the body hole.

(f) Make sure there is no play in the installed floor side airbag sensor parts.

3. INSTALL CENTER PILLAR LOWER GARNISH

Click here

4. CONNECT REAR DOOR SCUFF PLATE WEATHERSTRIP

5. INSTALL REAR DOOR SILL PLATE (with rear seat side airbag)

Click here

6. INSTALL REAR DOOR SILL PLATE (without rear seat side airbag)

Click here

7. CONNECT FRONT DOOR SCUFF PLATE WEATHERSTRIP

8. INSTALL FRONT DOOR SILL PLATE

Click here

9. CONNECT FRONT SEAT BELT OUTER BELT ASSEMBLY

Click here

10. INSTALL SEAT BELT OUTER ANCHOR COVER

Click here

11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click here

NOTICE:

When the cable has been disconnected, some systems must be reset after the cable is reconnected.

Click here

12. PERFORM DIAGNOSTIC SYSTEM CHECK

Click here

13. CHECK SRS WARNING LIGHT

Click here