Removal
REMOVAL
PRECAUTION / NOTICE / HINT
The procedures required (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during gear shift control cable assembly removal/installation are shown below.
Procedure Required After Replacing / Removing / Installing PartsReplacement part or procedure | Required Procedure | Effect/Inoperative function when procedure not performed | Link |
|---|---|---|---|
Disconnect the cable from the negative (-) battery terminal. |
Initialize Back Door Lock |
Door Lock Control System |
|
Memorize Steering Angle Neutral Point |
Lane Departure Alert System (with Steering Control) |
||
Pre-Collision System |
|||
Gas leak in the exhaust system |
Verification after Repair |
|
CAUTION:
- When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.
.png)
- Contact with high-temperature areas such as the engine and exhaust pipe may cause burns.
PROCEDURE
1. PRECAUTIONS
NOTICE:
After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.
Click here
![]()
2. SECURE VEHICLE
(a) Fully apply the parking brake and chock a wheel.
CAUTION:
- Be sure to apply the parking brake and chock a wheel before performing this operation.

- If the vehicle is not secured and the shift lever is moved to the N position, the vehicle may move suddenly and cause an accident or serious injury.
3. DISCONNECT BATTERY NEGATIVE TERMINAL CABLE
Click here![]()
NOTICE:
When the cable has been disconnected, some systems must be reset after the cable is reconnected.
Click here
![]()
4. REMOVE BATTERY
Click here![]()
5. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
Click here![]()
6. REMOVE REAR CONSOLE BOX ASSEMBLY
Click here![]()
7. REMOVE ENGINE UNDER COVER NO. 1
Click here![]()
8. REMOVE ENGINE UNDER COVER REAR LH
Click here![]()
9. REMOVE VALVE COVER NO. 2
Click here![]()
10. REMOVE RADIATOR COVER
Click here![]()
11. REMOVE AIR CLEANER INLET NO. 1
Click here
![]()
12. REMOVE AIR CLEANER COVER WITH AIR CLEANER HOSE
Click here![]()
13. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Click here![]()
14. REMOVE ECM
Click here![]()
15. REMOVE BATTERY CLAMP SUB-ASSEMBLY
Click here![]()
16. REMOVE FRONT FLOOR LH COVER (with cover)
Click here
![]()
17. REMOVE FRONT FLOOR RH COVER (with cover)
HINT:
Perform the same procedure as for the left side.
18. REMOVE FRONT FLOOR CENTER BRACE
Click here
![]()
19. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: front and rear catalytic converter)
Click here
![]()
20. REMOVE FRONT FLOOR HEAT INSULATOR NO. 1
(a) Remove the 3 nuts and the front floor heat insulator No. 1 from the vehicle body. |
![]() |
21. REMOVE GEAR SHIFT CONTROL CABLE ASSEMBLY
(a) Place the shift lever in the N position.
![]() |
Remove in this direction |
(b) Disconnect the end of the gear shift control cable assembly from the floor shift lever assembly.
*1 |
Slider |
![]() |
Push in |
![]() |
Remove in this direction |
(c) Push the slider and remove the gear shift control cable from the floor shift lever assembly as shown in the illustration.
(d) Remove the nut to disconnect the gear shift control cable assembly from the control shaft lever. |
![]() |
(e) Remove the clip to disconnect the gear shift control cable assembly from the gear shift control cable bracket No. 1.
(f) Remove the nut to disconnect the gear shift control cable assembly from the gear shift control cable bracket. |
![]() |
(g) Remove the nut. |
![]() |
(h) Release the guide to disconnect the gear shift control cable assembly from the vehicle body.
(i) Remove the 2 nuts and the gear shift control cable assembly from the vehicle body. |
![]() |
.gif)

.png)
.png)



