Installation
INSTALLATION
PROCEDURE
1. INSTALL GEAR SHIFT CONTROL CABLE ASSEMBLY
(a) Pass the shift control cable assembly into the vehicle, then install the shift control cable assembly to the vehicle body using the 2 nuts. Torque: 5 N·m {51 kgf·cm, 44 in·lbf} |
![]() |
(b) Engage the guide to connect the shift control cable assembly to the vehicle body. |
![]() |
(c) Install the nut.
Torque:
5 N·m {51 kgf·cm, 44 in·lbf}
(d) Install the shift control cable assembly to the shift control cable bracket using the nut. Torque: 5 N·m {51 kgf·cm, 44 in·lbf} |
![]() |
(e) Turn the control shaft lever clockwise until it stops, then turn it 2 notches counterclockwise. |
|
(f) Install the shift control cable assembly to the shift control cable bracket using a new clip.
(g) Connect the shift control cable assembly to the control shaft lever with the nut.
Torque:
12 N·m {122 kgf·cm, 9 ft·lbf}
(h) Connect the shift control cable assembly to the floor shift lever assembly.
NOTICE:
Make sure the shift control cable assembly is securely locked.
![]() |
Install in this direction |
(i) Connect the end of the shift control cable assembly to the floor shift lever assembly.
NOTICE:
- Before connecting the shift control cable assembly, make sure the park/neutral position switch and the shift lever are in the N position.
- Install the end of the shift control cable assembly so that the lock piece faces the driver side.
- Fully install the end of the shift control cable assembly to the base of the pin.
![]() |
Install in this direction |
2. ADJUST SHIFT LEVER POSITION
Click here![]()
3. INSTALL NO. 1 FRONT FLOOR INSULATOR
(a) Install the No. 1 front floor insulator to the vehicle body using the 3 nuts.
Torque:
5 N·m {51 kgf·cm, 44 in·lbf}
4. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalytic Converter)
Click here
![]()
5. INSTALL FRONT FLOOR CENTER BRACE
Click here
![]()
6. INSTALL LH FRONT FLOOR PANEL COVER (with Cover)
Click here
![]()
7. INSTALL RH FRONT FLOOR PANEL COVER (with Cover)
HINT:
Perform the same procedure as for the left side.
8. INSTALL BATTERY CLAMP SUB-ASSEMBLY
Click here![]()
9. INSTALL ECM
Click here![]()
10. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Click here![]()
11. INSTALL AIR CLEANER COVER WITH AIR CLEANER HOSE
Click here![]()
12. INSTALL NO. 1 AIR CLEANER INLET
Click here
![]()
13. INSTALL RADIATOR COVER
Click here![]()
14. INSTALL REAR CONSOLE BOX ASSEMBLY
Click here![]()
15. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
Click here![]()
16. INSTALL BATTERY
Click here![]()
17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Click here![]()
NOTICE:
When the cable has been disconnected, some systems must be reset after the cable is reconnected.
Click here
![]()
18. CHECK SHIFT LEVER POSITION
Click here![]()
19. CHECK FOR EXHAUST GAS LEAKAGE
Click here![]()
HINT:
After repairing or replacing the exhaust system, perform the "Verification After Repair" procedure.
Click here![]()
20. INSTALL NO. 2 VALVE COVER
Click here![]()
21. INSTALL REAR LH ENGINE UNDER COVER
Click here![]()
22. INSTALL NO. 1 ENGINE UNDER COVER
Click here![]()
.png)
.png)
.png)

.png)