Introduction

General Information

~5min read

GENERAL INFORMATION

  • The vehicle is equipped with a large number of systems controlled by ECUs. ECU-controlled systems are generally considered very complex and require advanced technical knowledge to troubleshoot. However, most inspection procedures simply consist of checking the circuits of the ECU-controlled systems one by one. If you correctly understand how the system operates and have basic electrical knowledge, it is possible to perform efficient troubleshooting, make an accurate diagnosis and carry out the necessary repairs.
  • (using the Techstream*)

    HINT:

    *: Techstream is the name of the diagnostic tester in North America.

    • Before using the Techstream, carefully read the Techstream operator's manual.
    • If the Techstream cannot communicate with the ECU-controlled systems while it is connected to the DLC3, the ignition switch is ON and the Techstream is turned on, there is a problem on the vehicle or on the Techstream.
      1. If communication is possible when the Techstream is connected to another vehicle, check the diagnostic data link line (bus (+) line), the CANH and CANL lines, and the power supply circuits for the vehicle's ECUs.
      2. If communication remains impossible when the Techstream is connected to another vehicle, the problem is most likely in the Techstream itself. Perform the self-test described in the Techstream operator's manual.

TROUBLESHOOTING PROCEDURES

  • Troubleshooting procedures include diagnostic procedures when a DTC is stored and diagnostic procedures when no DTC is stored. The basic concept is explained in the following table.

    Procedure type

    Details

    Troubleshooting method

    DTC-based diagnosis

    The diagnostic procedure is based on the stored DTC.

    The defective part is identified based on the DTC detection conditions using a process of elimination.

    Potential faulty parts are eliminated one by one using the Techstream and by checking the relevant parts.

    Symptom-based diagnosis

    (No DTC stored)

    The diagnostic procedure is based on the symptoms of the problem.

    The defective part is identified based on the symptoms of the problem using a process of elimination.

    Potential faulty parts are eliminated one by one using the Techstream and by checking the relevant parts.

  • Vehicle systems are complex and use many ECUs that are difficult to check individually. For this reason, a process of elimination is used: the component parts that can be checked individually are checked first and, if no fault is found in these components, the corresponding ECU is identified as the cause of the problem and is replaced.
  • It is extremely important to ask the customer about the environment and conditions present when the problem occurred (analysis of the customer's complaint). This makes it possible to simulate the conditions and confirm the symptom. If the symptom cannot be confirmed or the DTC does not reappear, the faulty part may not be identified using the troubleshooting procedure, and the ECU for the corresponding system may be replaced even though it is not faulty. In that case, the original problem will not be resolved.
  • To avoid endless troubleshooting procedures, the troubleshooting procedures are written on the assumption that several malfunctions do not occur simultaneously for a single symptom.
  • To identify the faulty part, the troubleshooting procedures narrow down the target by separating the component parts, ECUs and wire harnesses during inspection. If the wire harness is identified as the cause of the problem, it is necessary to check not only the connections at the component parts and ECUs, but also all connectors in the wire harness between the component part and the ECU.

DESCRIPTION

(a) The data of each system and the diagnostic trouble codes (DTCs) can be read using the vehicle's Data Link Connector 3 (DLC3). If the system appears not to operate correctly, check for possible malfunctions using the Techstream and perform repairs.

CHECK DLC3

(a) The vehicle's ECUs use the ISO 15765-4 communication protocol. The DLC3 terminal arrangement complies with the SAE J1962 standard and conforms to the ISO 15765-4 format.

Symbol

Terminal No.

Name

Reference terminal

Result

Condition

SIL

7

Bus line "+"

5 - Signal ground

Pulse generation

During transmission

CG

4

Chassis ground

Body ground

1 Ω maximum

Always

SG

5

Signal ground

Body ground

1 Ω maximum

Always

BAT

16

Battery positive

Body ground

11 à 14 V

Always

CANH

6

CAN "High" line

14 - CANL

54 à 69 Ω

Ignition switch in OFF position*

Battery positive

6 kΩ or higher

Ignition switch in OFF position*

4 - CG

200 Ω or higher

Ignition switch in OFF position*

CANL

14

CAN "Low" line

Battery positive

6 kΩ or higher

Ignition switch in OFF position*

4 - CG

200 Ω or higher

Ignition switch in OFF position*

NOTICE:

*: Before measuring the resistance, leave the vehicle at rest for at least 1 minute and do not operate the ignition switch, any other switch or any door.

If the result does not meet the specifications, there may be a malfunction in the DLC3. Repair or replace the wire harness or connector.