How to Use Troubleshooting
HOW TO USE TROUBLESHOOTING
WORK FLOW
HINT:
Perform troubleshooting in accordance with the procedure shown below. The following is a description of the basic troubleshooting procedure. Confirm the troubleshooting procedure to follow for the relevant circuit before starting troubleshooting.
1. VEHICLE BROUGHT TO WORKSHOP
2. CUSTOMER COMPLAINT ANALYSIS
(a) Ask the customer to describe the driving conditions and external conditions under which the problem occurred.
3. CHECK BATTERY VOLTAGE
(a) Measure the battery voltage.
Standard voltage:
11 à 14 V
If the voltage is below 11 V, charge or replace the battery before proceeding to the next step.
4. CONFIRM SYMPTOM AND CHECK DTCs (AND FREEZE FRAME DATA)
(a) Visually check the wire harnesses, connectors and fuses for any breaks or short circuits.
(b) Warm up the engine to its normal operating temperature.
(c) Confirm the symptoms of the problem and the conditions, then check the DTCs.
Result:
Result | Proceed to |
|---|---|
DTCs are output |
Go to step 5 |
No DTCs are output |
Go to step 6 |
5. DTC CHART
(a) Identify the DTCs output in the DTC chart. Refer to the "Suspected Area" column for the list of circuits and/or parts that may be faulty.
Result:
Go to step 7
6. SYMPTOM CHART
(a) Identify the symptoms in the symptom chart. Refer to the "Suspected Area" column for the list of circuits and/or parts that may be faulty.
7. CHECK CIRCUITS OR COMPONENT PARTS
(a) Identify the faulty circuit or part.
8. ADJUST, REPAIR OR REPLACE
(a) Adjust, repair or replace the faulty circuit or component parts.
9. CONFIRMATION TEST
(a) Once adjustment, repair or replacement of the component parts is fully completed, make sure the malfunction no longer occurs. If the malfunction does not reappear, perform a confirmation test under driving conditions and external conditions similar to those in which the problem first occurred.
(b) END
CUSTOMER PROBLEM ANALYSIS
HINT:
- When troubleshooting, make sure the symptoms of the problem have been correctly identified. Any preconceptions must be set aside in order to make an accurate judgment. To clearly understand the actual symptoms of the problem, it is essential to ask the customer about the nature of the problem and the conditions under which it occurred.
- Gather as much information as possible for reference. Previous problems that do not appear related to the current problem may also be very useful in some cases.
- The following 5 elements are essential for analyzing the problem:
What
Vehicle model, system name
When
Date, time, frequency of occurrence
Where
Road conditions
What were the conditions?
Driving conditions, weather conditions
How did it happen?
Problem Symptoms
SYMPTOM CONFIRMATION AND DIAGNOSTIC CODE
HINT:
The vehicle diagnostic system performs several functions.
- The first function is DTC checking. A DTC is a code stored in the ECU memory as soon as a malfunction occurs in the signal circuits connected to the ECU. When checking DTCs, the DTCs recorded by a previous malfunction can be checked by the technician during troubleshooting.
- Another function is input signal checking, which verifies whether the signals from the various switches are correctly sent to the ECU.
These functions make it possible to identify the problem and carry out effective troubleshooting. The diagnostic functions are built into the following vehicle systems.
System
Symptom Confirmation and Diagnostic Code
DTC Check
(normal mode)
DTC Check
(check mode)
Sensor Check Mode / Test Mode (Input Signal Check)
Data List
Active Test
SFI System
○
○
-
○
○
Ignition system
-
-
-
-
-
Fuel system
-
-
-
-
-
Emission control system
-
-
-
-
-
Intake system
-
-
-
-
-
Cooling fan system
-
-
-
-
-
Cruise Control System
○
-
-
○
○
Dynamic Radar Cruise Control System
○
-
-
○
○
Front Recognition Camera System
○
-
-
○
○
Lane Departure Alert System (with Steering Control)
○
-
-
○
○
Continuously Variable Transaxle System
○
○
-
○
○
Tire Pressure Warning System
○
-
○
○
○
Vehicle Stability Control System
○
-
○
○
○
Electric parking brake system
○
-
-
○
○
Steering lock system
○
-
-
○
○
Power steering system
○
-
-
○
-
Audio and Visual System (for Radio Receiver Type)
-
-
-
-
-
Audio and Visual System (for Radio and Display Type)
○
-
-
○
-
Navigation System
○
-
-
○
-
Blind Spot Monitor System
○
-
-
○
-
Rear view monitor system
-
-
-
-
-
Safety Connect System
○
-
-
○
-
Toyota Entune System
○
-
-
-
-
Charging system
○
-
-
○
○
LIN Communication System
○
-
-
○
-
CAN communication system
○
-
-
○
-
Door Lock Control System
-
-
-
○
○
Remote Power Door Lock Control System (with Smart Key System)
○
-
-
○
○
Remote Keyless Entry System (without Smart Key System)
-
-
-
○
○
Key Reminder System
-
-
-
○
-
Smart Key System (for Entry Function)
○
-
-
○
○
Smart Key System (for Start Function)
○
-
-
○
○
Immobilizer System (with Smart Key System)
○
-
-
○
○
Immobilizer System (without Smart Key System)
○
-
-
○
○
Theft deterrent system
-
-
-
○
○
Lighting System (INT)
-
-
-
○
○
Glass Defogger System
-
-
-
-
○
Windshield Deicer System
-
-
-
-
○
Meter / Gauge System
○
-
-
○
○
Combination Meter System
-
-
-
-
-
Airbag System
○
○
-
○
-
Pre-Collision System
○
-
-
○
○
Front Power Seat System
-
-
-
-
-
Seat Heater System
-
-
-
-
-
Seat Belt Reminder System
-
-
-
○
○
Air Conditioning System (for Automatic Air Conditioning System with Air Conditioning Pressure Sensor Mounted on Top)
○
-
-
○
○
Air Conditioning System (for Automatic Air Conditioning System with Air Conditioning Pressure Sensor Mounted on Side)
○
-
-
○
○
Accessory Socket System
-
-
-
-
-
Power Window Control System
○
-
-
○
○
Fuel Filler Door Opener System
-
-
-
-
-
Power Mirror Control System
-
-
-
○
○
Windshield Wiper and Washer System
-
-
-
-
-
Lighting System (EXT)
○
-
-
○
○
Automatic Headlight Leveling System
○
-
-
○
○
Auto High Beam System
○
-
-
○
-
Horn System
-
-
-
-
○
- When checking DTCs, it is very important to determine whether the malfunction indicated by a DTC: 1) is still occurring, or 2) occurred in the past but the system has returned to normal. In addition, the DTC must be compared with the malfunction symptom to see whether they are related. For this reason, DTCs must be checked before and after confirming the symptoms (i.e. whether the symptoms of a malfunction are still occurring or not) in order to determine the current condition of the system, as shown in the table below.
- Never omit checking DTCs. Depending on the case, omitting the DTC check may result in unnecessary troubleshooting for systems operating normally, or in repairs unrelated to the malfunction. Follow the procedure shown in the table in the correct order.
- The following flowchart shows the troubleshooting procedure using DTC checks. The instructions explain how to troubleshoot based on DTCs or based on the symptom table for each malfunction.
1. CHECK DTC
2. RECORD DTCS DISPLAYED, THEN CLEAR
3. CONFIRM SYMPTOMS
Result:
Result | Proceed to |
|---|---|
No Symptoms |
Go to step 4 |
Symptoms |
Go to step 5 |
4. SIMULATION TEST USING SYMPTOM SIMULATION METHODS
5. CHECK DTC
Result:
Result | Proceed to |
|---|---|
No DTCs are output |
Go to step 6 |
DTCs are output |
TROUBLESHOOT THE MALFUNCTION INDICATED BY THE DTC |
6. CONFIRM SYMPTOMS
Result:
Result | Proceed to |
|---|---|
Symptoms |
TROUBLESHOOT EACH MALFUNCTION SYMPTOM |
No Symptoms |
END |
If a DTC is displayed during the initial diagnostic trouble code check, this may indicate that a malfunction occurred in the wire harness or connector of this circuit in the past. Check the wire harness and connectors.
If malfunction symptoms are detected, but no DTC is recorded again after clearing, the cause of the symptom is a part that is not involved in recording DTCs (the DTC displayed during the initial check was certainly the result of a past or secondary malfunction).
SIMULATE SYMPTOMS
HINT:
The most difficult case in troubleshooting is when there are no symptoms. In such a situation, analyze very carefully the problem described by the customer. Then reproduce the driving conditions and external conditions under which the problem occurred on the customer's vehicle. Regardless of the technician's skill or experience, troubleshooting without confirming the symptoms of a malfunction will lead to omitted important repairs and cause errors or delays.
Example:
If an abnormality occurs only when the engine is cold, or is caused by vibration from road bumps, it is impossible to identify the problem while checking symptoms with the vehicle stationary or when the engine is warm. Vibration, heat or water infiltration (moisture) are difficult to reproduce. The following symptom simulation tests are effective substitutes for actual conditions and can be applied to a stationary vehicle. Important points to remember when performing symptom simulation tests:
During symptom simulation tests, the malfunction symptoms must be confirmed, as must the area or parts at fault. First identify the circuits likely to be faulty based on the symptoms. Then connect the tester and perform symptom simulation tests, determining whether the circuit being checked is faulty or not. Also confirm the malfunction symptoms. Refer to the malfunction symptom table for each system to accurately identify the potential causes of the malfunction.
In order to reproduce DTCs, it is necessary to satisfy the detection conditions of the DTC concerned.
(a) VIBRATION METHOD: When a malfunction seems to occur due to vibration.
*a |
Lightly vibrate |
*b |
Lightly shake |
(1) COMPONENT PARTS OR SENSORS
Lightly vibrate the component part or sensor suspected of causing the malfunction with your finger, and check whether the malfunction occurs.
NOTICE:
If relays are subjected to strong vibration, they may open.
(2) CONNECTORS
Lightly shake the connector vertically and horizontally.
(3) WIRE HARNESS
Lightly shake the wire harness vertically and horizontally.
HINT:
The connector seal and the vibration support point are the main areas to check carefully.
(b) HEAT METHOD: When a malfunction seems to occur when the affected area is subjected to heat.
(1) Heat the suspected component with an electric hair dryer or similar device. Check whether the problem occurs.
NOTICE:
- Do not heat the component parts to more than 60 °C. Exceeding this temperature may damage the component parts.
- Do not apply heat directly to ECU parts.
(c) WATER SPRINKLING METHOD: Use when a problem seems to occur in rainy weather or when humidity is high.
(1) Sprinkle water on the vehicle and check whether the malfunction occurs.
NOTICE:
- Never sprinkle water directly into the engine compartment. Change the temperature and humidity indirectly by sprinkling water on the front of the radiator.
- Never sprinkle water directly on electronic components.
HINT:
If the vehicle has or had water infiltration problems, these may have damaged the ECU or connectors. Look for signs of corrosion or short circuits. Use caution during water sprinkling tests.
(d) ELECTRICAL LOAD METHOD: Use when the malfunction seems to occur when a high electrical load is applied.
(1) Turn on the heater blower, headlights, rear window defogger, and apply all other electrical loads. Check whether the malfunction reoccurs.
DTC CHART
Check the diagnostic trouble codes (DTCs) output (from the DTC checks) in the diagnostic trouble code chart of the applicable section. Use the chart to determine the suspected component and the appropriate inspection procedure. A description of each column of the chart is shown below.
Item | Description |
|---|---|
DTC No. |
Indicates the diagnostic trouble code. |
Detection Item |
Indicates the system with the problem or details about it. |
DTC Detection Condition |
Indicates the condition under which a DTC is stored. |
Suspected Area |
Indicates the components that may be causing the problem. |
Link |
Indicates the page where the inspection procedure for each circuit is located, or gives instructions for performing the inspection and repair. |
SYMPTOM TROUBLESHOOTING TABLE
If no DTC is output but the problem persists, refer to the symptom troubleshooting chart. The chart below shows the circuits and parts that may be causing the symptom. The suspected components are listed in order of probability. A description of each column of the chart is shown below.
HINT:
In some cases, the diagnostic system cannot detect the problem even when a symptom occurs. The problem may occur outside the detection range of the diagnostic system or in a completely different system.
Item | Description |
|---|---|
Symptom |
- |
Suspected Area |
Indicates the circuit or part to be inspected. |
Link |
Indicates the page where the inspection procedure is located. |
INSPECTION
A description of the main inspection points for the affected areas is provided in the chart below.
Item | Description |
|---|---|
Description |
Explains the main role and operation of the circuit or system and its component parts. |
DTC No., DTC detection condition and trouble area |
Indicates the diagnostic trouble codes, DTC detection conditions and the areas that may cause the malfunction. |
Wiring Diagram |
Shows the wiring diagram of the circuit or system. This diagram can be used together with the electrical wiring diagram to fully understand the circuit. Wire colors are indicated using alphabetical codes. B = Black, L = Blue, R = Red, BR = Brown, LG = Light Green, V = Violet, G = Green, O = Orange, W = White, GR = Gray, P = Pink, Y = Yellow, SB = Sky Blue The first letter indicates the base color of the wire and the second letter indicates the color of the stripe. |
Procedure |
Indicates the procedure to determine whether the circuit is normal or not, and also to determine whether the problem is in the sensors, actuators, wire harnesses or ECU. |
ECU Connector Diagram During Inspection |
Indicates whether the connector being inspected is connected or disconnected. Electrical tester connections are indicated by (+) or (-) after the terminal name. For checks between a connector and body ground, ground information is not shown in the diagram. |