AT Solenoids Operation Shutdown Circuit Stuck Off (P17029F)
DESCRIPTION
The TCM continuously monitors its CPU. If the output of the CPU deviates from the standard, the TCM will illuminate the MIL and store this DTC.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P17029F |
AT Solenoids Operation Shutdown Circuit Stuck Off |
TCM main CPU malfunction (1 trip detection logic) |
TCM |
Comes on |
DTC stored |
SAE Code: P1702 |
MONITOR DESCRIPTION
The TCM monitors the current flow to the shift solenoid valves. When the ignition switch is ON, if the TCM detects that current is flowing to the shift solenoid valves even though current cut was requested, it will store this DTC.
MONITOR STRATEGY
Related DTCs |
P1702: TCM processor performance |
Required sensors/Components |
TCM |
Frequency of operation |
Once per driving cycle |
Duration |
2 times |
MIL operation |
Immediate |
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored |
None |
Ignition switch |
OFF to ON |
TYPICAL MALFUNCTION THRESHOLDS
Actuator cut circuit check |
Fail |
CONFIRMATION DRIVING PATTERN
HINT:
- After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
- When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.
Click here
.gif)
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
- Turn the ignition switch to ON and wait for 2 minutes or more. [*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
- Input the DTC: P17029F.
- Check the DTC judgment result.
GTS Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
NOTICE:
- Perform the universal trip to clear permanent DTCs.
Click here
.gif)
- Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click here
.gif)
- Check that no DTCs are stored after performing initialization.
Click here
.gif)
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
.gif)
PROCEDURE
CLEAR DTC
(a) Clear the DTCs.
Powertrain > Transmission > Clear DTCsHINT:
Write down the currently output DTCs before clearing them.
(b) Turn the ignition switch off.
|
CHECK DTC OUTPUT (DTC P17029F)
(a) Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.
(b) Connect the cable to the negative (-) auxiliary battery terminal.
(c) Turn the ignition switch to ON and wait for 1 minute or more.
(d) Turn the ignition switch off and wait for 2 minutes or more.
HINT:
This DTC is detected after the ignition switch is turned off.
(e) Enter the following menus:
Powertrain > Transmission > Trouble Codes(f) Read the DTCs using the GTS.
Result | Proceed to |
|---|---|
DTCs are not output |
A |
DTC P17029F is output |
B |
| A | CHECK FOR INTERMITTENT PROBLEMS Click here Click here |
|
REPLACE TCM
Click here
![]()
| NEXT | PERFORM REGISTRATION AND INITIALIZATION for Registration: Click here for Initialization: Click here |