TCM Processor Watchdog/Safety MCU Failure (P061347)
DESCRIPTION
The TCM continuously monitors its CPU. If the output of the CPU deviates from the standard, the TCM will illuminate the MIL and store this DTC.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P061347 |
TCM Processor Watchdog/Safety MCU Failure |
TCM CPU malfunction (1-trip detection logic) |
TCM |
Comes on |
DTC stored |
SAE Code: P0613 |
MONITOR STRATEGY
Related DTC |
P0613: TCM processor performance |
Required Sensors/Components (Main) |
TCM |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
Condition (A): 3 times Condition (B): 2 times |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored |
None |
TYPICAL MALFUNCTION THRESHOLDS
Condition (A):One of the following conditions is met |
- |
ROM check sum |
Error |
RAM read and write check |
Fail |
One of the following conditions is met |
- |
Specific software routine A operation period check |
Fail |
Software functional check |
Fail |
CONFIRMATION DRIVING PATTERN
HINT:
- After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
- When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.
Click here
.gif)
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the GTS off.
- Turn the ignition switch off.
- Disconnect the GTS.
- Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.
- Connect the cable to the negative (-) auxiliary battery terminal.
- Turn the ignition switch to ON.
- Wait for 1 second or more. [*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
- Input the DTC: P061347.
- Check the DTC judgment result.
GTS Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
NOTICE:
- Perform the universal trip to clear permanent DTCs.
Click here
.gif)
- Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click here
.gif)
- Check that no DTCs are stored after performing initialization.
Click here
.gif)
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
.gif)
HINT:
Read Freeze Frame Data using the GTS. The TCM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CLEAR DTC
(a) Clear the DTCs.
Powertrain > Transmission > Clear DTCs(b) Turn the ignition switch off.
|
CHECK DTC OUTPUT (DTC P061347)
(a) Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.
(b) Connect the cable to the negative (-) auxiliary battery terminal.
(c) Turn the ignition switch to ON.
(d) Wait for 1 second or more.
(e) Read the DTCs.
Powertrain > Transmission > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTC P061347 is output |
B |
| A | CHECK FOR INTERMITTENT PROBLEMS Click here Click here |
|
REPLACE TCM
Click here
![]()
| NEXT | PERFORM REGISTRATION AND INITIALIZATION for Registration: Click here for Initialization: Click here |