Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
BODY SIDE NAME PLATE |
75473C |
- |
- |
|
*A |
for AWD |
*B |
for LH Side |
*C |
for RH Side |
- |
- |
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
2 |
REAR DOOR OUTSIDE LOWER MOULDING SUB-ASSEMBLY LH |
75078 |
- |
- |
- |
3 |
REAR DOOR OUTSIDE LOWER MOULDING SUB-ASSEMBLY RH |
75077 |
- |
- |
- |
4 |
HOLE PLUG |
- |
- |
- |
- |
*A |
for AWD |
*B |
for LH Side |
*C |
for RH Side |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
5 |
NO. 5 BACK DOOR NAME PLATE |
75445A |
- |
- |
|
6 |
NO. 2 BACK DOOR NAME PLATE |
75442A |
- |
- |
|
7 |
NO. 4 LUGGAGE COMPARTMENT DOOR NAME PLATE |
75444C |
- |
- |
|
8 |
NO. 4 LUGGAGE COMPARTMENT DOOR NAME PLATE |
75444C |
- |
- |
|
9 |
SYMBOL EMBLEM |
75741E |
- |
- |
|
*A |
for AWD |
*B |
for HEV Model |
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
10 |
NO. 4 BACK DOOR NAME PLATE |
75444A |
- |
- |
|
11 |
NO. 4 BACK DOOR NAME PLATE |
75444A |
- |
- |
|
12 |
NO. 4 BACK DOOR NAME PLATE |
75444A |
- |
- |
|
13 |
NO. 4 BACK DOOR NAME PLATE |
75444A |
- |
- |
|
*A |
for Type A |
*B |
for Type B |
*C |
for Type C |
*D |
for Type D |
● |
Non-reusable part |
- |
- |
![]() |
NOTICE: When installing the new name plates or emblems, heat the vehicle body, name plates or emblems using a heat light. |
Standard:
Item | Temperature |
|---|---|
Vehicle Body |
40 to 60 °C |
|
20 to 30 °C |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
*a |
Heated Part |
*b |
Heat Light |
NOTICE:
Do not heat vehicle body, name plates or emblems excessively.
PROCEDURE
1. INSTALL BODY SIDE NAME PLATE (for AWD)
(a) for LH Side:
*a |
Reference Values |
*b |
Center of Hole |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
88.6 mm (3.488 in.) |
B |
8.0 mm (0.315 in.) |
C |
2.2 mm (0.087 in.) |
D |
97 mm (3.819 in.) |
(1) Clean the vehicle body surface.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the body side name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new body side name plate.
1. Using a heat light, heat the vehicle body and body side name plate.
2. Remove the release paper from the body side name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the body side name plate as shown in the illustration.
HINT:
Press the body side name plate firmly to install it.
(b) for RH Side:
*a |
Reference Values |
*b |
Center of Hole |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
97 mm (3.819 in.) |
B |
1.2 mm (0.047 in.) |
C |
4.5 mm (0.177 in.) |
D |
88.6 mm (3.488 in.) |
(1) Clean the vehicle body surface.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the body side name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new body side name plate.
1. Using a heat light, heat the vehicle body and body side name plate.
2. Remove the release paper from the body side name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the body side name plate as shown in the illustration.
HINT:
Press the body side name plate firmly to install it.
2. INSTALL REAR DOOR OUTSIDE LOWER MOULDING SUB-ASSEMBLY LH (for AWD)
3. INSTALL REAR DOOR OUTSIDE LOWER MOULDING SUB-ASSEMBLY RH (for AWD)
4. INSTALL HOLE PLUG (for AWD)
5. INSTALL NO. 5 BACK DOOR NAME PLATE
*a |
Reference Values |
*b |
End of R |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
47.5 mm (1.870 in.) |
B |
209.6 mm (8.252 in.) |
C |
230.9 mm (9.091 in.) |
D |
233.3 mm (9.185 in.) |
(1) Clean the vehicle body surface.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the No. 5 back door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new No. 5 back door name plate.
1. Using a heat light, heat the vehicle body and No. 5 back door name plate.
2. Remove the release paper from the No. 5 back door name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 5 back door name plate as shown in the illustration.
HINT:
Press the No. 5 back door name plate firmly to install it.
6. INSTALL NO. 2 BACK DOOR NAME PLATE
*a |
Reference Values |
*b |
End of R |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
49.1 mm (1.933 in.) |
B |
178.1 mm (7.012 in.) |
C |
255.4 mm (10.055 in.) |
D |
258.2 mm (10.165 in.) |
(1) Clean the vehicle body surface.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the No. 2 back door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new No. 2 back door name plate.
1. Using a heat light, heat the vehicle body and No. 2 back door name plate.
2. Remove the release paper from the No. 2 back door name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 2 back door name plate as shown in the illustration.
HINT:
Press the No. 2 back door name plate firmly to install it.
7. INSTALL NO. 4 LUGGAGE COMPARTMENT DOOR NAME PLATE (for HEV Model)
*a |
Reference Values |
*b |
End of R |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
165.6 mm (6.520 in.) |
B |
29.7 mm (1.169 in.) |
C |
190.6 mm (7.504 in.) |
D |
186.9 mm (7.358 in.) |
(1) Clean the vehicle body surface.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the No. 4 luggage compartment door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new No. 4 luggage compartment door name plate.
1. Using a heat light, heat the vehicle body and No. 4 luggage compartment door name plate.
2. Remove the release paper from the No. 4 luggage compartment door name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 4 luggage compartment door name plate as shown in the illustration.
HINT:
Press the No. 4 luggage compartment door name plate firmly to install it.
8. INSTALL NO. 4 LUGGAGE COMPARTMENT DOOR NAME PLATE (for AWD)
*a |
Reference Values |
*b |
End of R |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
144 mm (5.669 in.) |
B |
55.5 mm (2.185 in.) |
C |
188.9 mm (7.437 in.) |
D |
186.5 mm (7.343 in.) |
(1) Clean the vehicle body surface.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the No. 4 luggage compartment door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new No. 4 luggage compartment door name plate.
1. Using a heat light, heat the vehicle body and No. 4 luggage compartment door name plate.
2. Remove the release paper from the No. 4 luggage compartment door name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 4 luggage compartment door name plate as shown in the illustration.
HINT:
Press the No. 4 luggage compartment door name plate firmly to install it.
9. INSTALL SYMBOL EMBLEM
*a |
Location Pin |
- |
- |
(1) Clean the vehicle body surface.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the symbol emblem with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new symbol emblem.
1. Using a heat light, heat the vehicle body and symbol emblem.
2. Remove the release paper from the symbol emblem.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Engage the location pins to install the symbol emblem as shown in the illustration..
HINT:
Press the symbol emblem firmly to install it.
10. INSTALL NO. 4 BACK DOOR NAME PLATE (for Type A)
*a |
Reference Values |
*b |
End of R |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
123.7 mm (4.870 in.) |
B |
65 mm (2.559 in.) |
C |
232.5 mm (9.154 in.) |
D |
230.7 mm (9.083 in.) |
(1) Clean the vehicle body surface.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the No. 4 back door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new No. 4 back door name plate.
1. Using a heat light, heat the vehicle body and No. 4 back door name plate.
2. Remove the release paper from the No. 4 back door name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 4 back door name plate as shown in the illustration.
HINT:
Press the No. 4 back door name plate firmly to install it.
11. INSTALL NO. 4 BACK DOOR NAME PLATE (for Type B)
*a |
Reference Values |
*b |
End of R |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
146.3 mm (5.760 in.) |
B |
51.2 mm (2.016 in.) |
C |
233 mm (9.173 in.) |
D |
230.3 mm (9.067 in.) |
(1) Clean the vehicle body surface.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the No. 4 back door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new No. 4 back door name plate.
1. Using a heat light, heat the vehicle body and No. 4 back door name plate.
2. Remove the release paper from the No. 4 back door name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 4 back door name plate as shown in the illustration.
HINT:
Press the No. 4 back door name plate firmly to install it.
12. INSTALL NO. 4 BACK DOOR NAME PLATE (for Type C)
*a |
Reference Values |
*b |
End of R |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
225.32 mm (8.871 in.) |
B |
226.12 mm (8.902 in.) |
C |
68.16 mm (2.683 in.) |
D |
22.8 mm (0.898 in.) |
(1) Clean the vehicle body surface.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the No. 4 back door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new No. 4 back door name plate.
1. Using a heat light, heat the vehicle body and No. 4 back door name plate.
2. Remove the release paper from the No. 4 back door name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 4 back door name plate as shown in the illustration.
HINT:
Press the No. 4 back door name plate firmly to install it.
13. INSTALL NO. 4 BACK DOOR NAME PLATE (for Type D)
*a |
Reference Values |
*b |
End of R |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
225.12 mm (8.863 in.) |
B |
226.47 mm (8.916 in.) |
C |
50.57 mm (1.991 in.) |
D |
22.8 mm (0.898 in.) |
(1) Clean the vehicle body surface.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the No. 4 back door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new No. 4 back door name plate.
1. Using a heat light, heat the vehicle body and No. 4 back door name plate.
2. Remove the release paper from the No. 4 back door name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 4 back door name plate as shown in the illustration.
HINT:
Press the No. 4 back door name plate firmly to install it.
.png)
.png)
.png)
.gif)
.png)