Toyota Land Cruiser Quiz
Body Electrical

Interior light system

In this manual: Body Electrical
Introduction — 13Preparation — 19Service specifications — 19Engine Mechanical — 28Automatic Transmission — 22Body Electrical — 373Brake — 34Propeller Shaft — 7Transfer — 24Motor shift control system — 1Steering — 34Ignition — 7Charging — 9Emission Control — 6Cooling — 17Starting — 12Lubrication — 13Maintenance — 7Chassis — 1Disassembly — 1
~3min read

INSPECTION

1. INSPECT FRONT PERSONAL LIGHT SWITCH CONTINUITY

INSPECT FRONT PERSONAL LIGHT SWITCH CONTINUITY
INSPECT FRONT PERSONAL LIGHT SWITCH CONTINUITY

If continuity is not as specified, replace the light assembly or bulb.

2. INSPECT REAR PERSONAL LIGHT SWITCH CONTINUITY

INSPECT REAR PERSONAL LIGHT SWITCH CONTINUITY
INSPECT REAR PERSONAL LIGHT SWITCH CONTINUITY

If continuity is not as specified, replace the light assembly or bulb.

3. INSPECT ROOM LIGHT SWITCH CONTINUITY

INSPECT ROOM LIGHT SWITCH CONTINUITY
INSPECT ROOM LIGHT SWITCH CONTINUITY

If continuity is not as specified, replace the light assembly or bulb.

4. INSPECT REAR ROOM LIGHT SWITCH CONTINUITY

INSPECT REAR ROOM LIGHT SWITCH CONTINUITY
(a) Disconnect the connector from room light assembly.

(b) Turn the room light switch ON, check that continuity exists between terminal 2 and body ground.

INSPECT REAR ROOM LIGHT SWITCH CONTINUITY

(c) Turn the room light switch DOOR, check that continuity exists between terminal 1 and 2.

If operation is not as specified, replace the light assembly or bulb.

5. INSPECT VANITY LIGHT CONTINUITY

INSPECT VANITY LIGHT CONTINUITY
INSPECT VANITY LIGHT CONTINUITY

If continuity is not as specified, replace the vanity light assembly or bulb.

6. INSPECT DOOR COURTESY SWITCH CONTINUITY

INSPECT DOOR COURTESY SWITCH CONTINUITY
(a) Check that continuity exists between terminal and switch body with the switch ON (switch pin released).

(b) Check that no continuity exists between terminal and switch body with the switch OFF (switch pin pushed).

If continuity is not as specified, replace the switch.

7. INSPECT DOOR COURTESY LIGHT CONTINUITY

INSPECT DOOR COURTESY LIGHT CONTINUITY

Using an ohmmeter, check that continuity exists between terminals.

If continuity is not as specified, replace the light assembly or bulb.

8. INSPECT BACK DOOR COURTESY SWITCH CONTINUITY

INSPECT BACK DOOR COURTESY SWITCH CONTINUITY
INSPECT BACK DOOR COURTESY SWITCH CONTINUITY

If continuity is not as specified, replace the back door lock assembly.

9. INSPECT GLOVE COMPARTMENT DOOR COURTESY SWITCH CONTINUITY

INSPECT GLOVE COMPARTMENT DOOR COURTESY SWITCH CONTINUITY
INSPECT GLOVE COMPARTMENT DOOR COURTESY SWITCH CONTINUITY

If continuity is not as specified, replace the switch

10. INSPECT LICENCE PLATE LIGHT CONTINUITY

INSPECT LICENCE PLATE LIGHT CONTINUITY

Using an ohmmeter, check that continuity exists between terminals.

If continuity is not as specified, replace the light assembly or bulb.

LOCATION

LOCATION
LOCATION

INSPECTION

1. INSPECT FRONT PERSONAL LIGHT SWITCH CONTINUITY

INSPECT FRONT PERSONAL LIGHT SWITCH CONTINUITY
INSPECT FRONT PERSONAL LIGHT SWITCH CONTINUITY

If continuity is not as specified, replace the light assembly or bulb.

2. INSPECT REAR PERSONAL LIGHT SWITCH CONTINUITY

INSPECT REAR PERSONAL LIGHT SWITCH CONTINUITY
INSPECT REAR PERSONAL LIGHT SWITCH CONTINUITY

If continuity is not as specified, replace the light assembly or bulb.

3. INSPECT ROOM LIGHT SWITCH CONTINUITY

INSPECT ROOM LIGHT SWITCH CONTINUITY
INSPECT ROOM LIGHT SWITCH CONTINUITY

If continuity is not as specified, replace the light assembly or bulb.

4. INSPECT REAR ROOM LIGHT SWITCH CONTINUITY

INSPECT REAR ROOM LIGHT SWITCH CONTINUITY
(a) Disconnect the connector from room light assembly.

(b) Turn the room light switch ON, check that continuity exists between terminal 2 and body ground

INSPECT REAR ROOM LIGHT SWITCH CONTINUITY

(c) Turn the room light switch DOOR, check that continuity exists between terminal 1 and 2.

If operation is not as specified, replace the light assembly or bulb.

5. INSPECT VANITY LIGHT CONTINUITY

INSPECT VANITY LIGHT CONTINUITY
INSPECT VANITY LIGHT CONTINUITY

If continuity is not as specified, replace the vanity light assembly or bulb.

6. INSPECT DOOR COURTESY SWITCH CONTINUITY

INSPECT DOOR COURTESY SWITCH CONTINUITY
(a) Check that continuity exists between terminal and switch body with the switch ON (switch pin released).

(b) Check that no continuity exists between terminal and switch body with the switch OFF (switch pin pushed).

If continuity is not as specified, replace the switch.

7. INSPECT DOOR COURTESY LIGHT CONTINUITY

INSPECT DOOR COURTESY LIGHT CONTINUITY

Using an ohmmeter, check that continuity exists between terminals.

If continuity is not as specified, replace the light assembly or bulb.

8. INSPECT BACK DOOR COURTESY SWITCH CONTINUITY

INSPECT BACK DOOR COURTESY SWITCH CONTINUITY
INSPECT BACK DOOR COURTESY SWITCH CONTINUITY

If continuity is not as specified, replace the back door lock assembly.

9. INSPECT GLOVE COMPARTMENT DOOR COURTESY SWITCH CONTINUITY

INSPECT GLOVE COMPARTMENT DOOR COURTESY SWITCH CONTINUITY
INSPECT GLOVE COMPARTMENT DOOR COURTESY SWITCH CONTINUITY

If continuity is not as specified, replace the switch.

10. INSPECT LICENCE PLATE LIGHT CONTINUITY

INSPECT LICENCE PLATE LIGHT CONTINUITY

Using an ohmmeter, check that continuity exists between terminals.

If continuity is not as specified, replace the light assembly or bulb.

LOCATION

LOCATION
LOCATION

Test yourself

A quick Toyota Land Cruiser quiz: every answer comes with an explanation and a link to the manual page.