Toyota RAV4 Quiz
Brake control

Installation

In this manual: Brake control
Introduction — 37Interior — 12Exterior — 432Az-fe engine mechanical — 1552Az-fe ignition — 182Az-fe charging — 232Az-fe emission control — 82az-fe exhaust — 32Az-fe fuel — 72Az-fe lubrication — 4Brake — 17Brake control — 63U140f automatic transaxle — 59Instrument panel — 8Suspension — 18Drive shaft — 23Axle — 6Tire and wheel — 30Air conditioning — 93Lighting — 45Cruise control — 21Differential — 12Door lock — 31Engine immobiliser — 21Horn — 5Can communication — 27Mirror — 5Parking brake — 5Power steering — 27Propeller shaft — 3Seat — 29Seat belt — 27Sliding roof — 25Steering column — 6Wiper and washer — 11Supplemental restraint system — 95Other system — 5Maintenance — 14
8steps
~48min
2/5difficulty
Done 0 of 8
Hint:
  • Use the same procedures for the lh side and rh side.
  • The procedures listed below are for the lh side.
  1. Install speed sensor front lh
Notice:

To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.

  1. Set the sensor body to the knuckle, and then install the sensor with the bolt.
Torque: 8.5 N*m (87 kgf*cm, 75 in.*Lbf)
Toyota RAV4. Install speed sensor front lh

Notice:
  • Keep the sensor tip and sensor installation hole free from foreign matter.
  • Firmly insert the sensor body into the knuckle before tightening the bolt.
  • After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
  • To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.
  1. Install the sensor clamp and sensor clip as follows.
Toyota RAV4. Install speed sensor front lh

  1. Set the flexible hose clamp on the flexible hose bracket.
  2. Simultaneously perform the following: 1) hang the hook part of the sensor clamp (labeled a) on the flexible hose bracket (labeled c); and 2) insert the hook part of the sensor clamp (labeled b) into the flexible hose bracket (labeled d).
Notice:

Do not twist the sensor wire when installing the clamp.

  1. Tighten together the sensor clamp, flexible hose clamp and flexible hose bracket with the bolt (labeled e).
Torque: 18.5 N*m (189 kgf*cm, 14 ft.*Lbf)
  1. Insert the sensor clip (labeled f) into the hole on the absorber lower bracket.
  2. Install the sensor clamp, and sensor clip as follows.
  3. Set the sensor clamp (labeled g) on the side member, and then tighten it with the bolt (labeled h).
Torque: 8.5 N*m (87 kgf*cm, 75 in.*Lbf) Notice:

Do not twist the sensor wire when installing the clamp.

  1. Insert the sensor clip (labeled i) into the hole on the apron.
Toyota RAV4. Install speed sensor front lh

  1. Connect the sensor connector.
Toyota RAV4. Install speed sensor front lh

  1. Install front fender liner lh
Toyota RAV4. Install front fender liner lh

Hint:

Install the fender liner so that the sensor wire harness passes beyond the fender liner installation clip towards the rear side of the vehicle.

  1. Install front wheel
Torque: 103 n*m (1,050 kgf*cm, 76 ft.*Lbf)
  1. Connect cable to negative battery terminal
  2. Check abs speed sensor signal
  3. Check the speed sensor signal (see page bc-28).

Test yourself

A quick Toyota RAV4 quiz: every answer comes with an explanation and a link to the manual page.