Toyota RAV4 (XA50) 2019-2026 Owners Manual: RCTA function

■ Operation of the RCTA function

The RCTA function uses rear side radar sensors to detect vehicles approaching from the right or left at the rear of the vehicle and alerts the driver of the presence of such vehicles by flashing the outside rear view mirror indicators and sounding a buzzer.

1
Approaching vehicles
2
Detection areas of approaching vehicles

■ RCTA icon display

When a vehicle approaching from the right or left at the rear of the vehicle is detected, the following will be displayed on the Multimedia display.

Example (Panoramic view monitor) (if equipped): Vehicles are approaching from both sides of the vehicle

■ RCTA function detection areas

The areas that vehicles can be detected in are outlined below.

The buzzer can alert the driver of faster vehicles approaching from farther away.

Example:

■The RCTA function is operational when

The RCTA function operates when all of the following conditions are met:

The engine switch is in ON.
The RCTA function is on.
The shift lever is in R.
The vehicle speed is less than approximately 15 km/h.
The approaching vehicle speed is between approximately 8 km/h and 56 km/h.

■Setting the buzzer volume

The buzzer volume can be adjusted on the multi-information display.

The volume of the RCTA buzzer can be adjusted on of the
multi-information display.

■Muting a buzzer temporarily

A mute button will be displayed on the multi-information display when a vehicles or an object is detected. To mute the buzzer, press .

The buzzers for the RCTA function and intuitive parking assist will be muted simultaneously.

Mute will be canceled automatically in the following situations:

When the shift lever is changed.
When the vehicle speed exceeds a certain speed.
When there is a malfunction in a sensor or the system is temporarily unavailable.
When the operating function is disabled manually.
When the engine switch is turned off.

■Conditions under which the system will not detect a vehicle

The RCTA function is not designed to detect the following types of vehicles and/or objects:

Vehicles approaching from directly behind
Vehicles backing up in a parking space next to your vehicle
Vehicles that the sensors cannot detect due to obstructions

Guardrails, walls, signs, parked vehicles and similar stationary objects*
Small motorcycles, bicycles, pedestrians, etc.*
Vehicles moving away from your vehicle
Vehicles approaching from the parking spaces next to your vehicle*
The distance between the sensor and approaching vehicle gets too close

*: Depending on the conditions, detection of a vehicle and/or object may occur.

■Situations in which the system may not operate properly

The RCTA function may not detect vehicles correctly in the following situations:

When the sensor is misaligned due to a strong impact to the sensor or its surrounding area
When mud, snow, ice, a sticker, etc., is covering the sensor or surrounding area on the rear bumper
When driving on a road surface that is wet with standing water during bad weather, such as heavy rain, snow, or fog
When multiple vehicles are approaching with only a small gap between each vehicle
When a vehicle is approaching at high speed
When equipment that may obstruct a sensor is installed, such as a towing eyelet, bumper protector (an additional trim strip, etc.), bicycle carrier, or snow plow
When backing up on a slope with a sharp change in grade

When backing out of a sharp angle parking spot

Immediately after the RCTA function is turned on
Immediately after the engine is started with the RCTA function on
When the sensors cannot detect a vehicle due to obstructions
When towing a trailer
When there is a significant difference in height between your vehicle and the vehicle that enters the detection area
When a sensor or the area around a sensor is extremely hot or cold
If the suspension has been modified or tires of a size other than specified are installed
If the front of the vehicle is raised or lowered due to the carried load
When turning while backing up

When a vehicle turns into the detection area

■Situations in which the system may operate even if there is no possibility of a collision

Instances of the RCTA function unnecessarily detecting a vehicle and/or object may increase in the following situations:

When the parking space faces a street and vehicles are being driven on the street

When the distance between your vehicle and metal objects, such as a guardrail, wall, sign, or parked vehicle, which may reflect electrical waves toward the rear of the vehicle, is short

When equipment that may obstruct a sensor is installed, such as a towing eyelet, bumper protector (an additional trim strip, etc.), bicycle carrier, or snow plow
When a vehicle passes by the side of your vehicle

When a detected vehicle turns while approaching the vehicle

When there are spinning objects near your vehicle such as the fan of an air conditioning unit
When water is splashed or sprayed toward the rear bumper, such as from a sprinkler
Moving objects (flags, exhaust fumes, large rain droplets or snowflakes, rain water on the road surface, etc.)
When the distance between your vehicle and a guardrail, wall, etc., that enters the detection area is short
Gratings and gutters
When a sensor or the area around a sensor is extremely hot or cold
If the suspension has been modified or tires of a size other than specified are installed
If the front of the vehicle is raised or lowered due to the carried load

RCTA function