Toyota Sienna Quiz
Supplemental restraint system

Open in Curtain Shield Squib RH Circuit

In this manual: Supplemental restraint system
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
16steps
~101min
4/5difficulty
1special tools
Done 0 of 16

DTC B1161/84 Open in Curtain Shield Squib RH Circuit

DESCRIPTION

The curtain shield squib RH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1161/84 is recorded when an open circuit is detected in the curtain shield squib RH circuit

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

  • Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester.
  • After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH)

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH)
  1. Turn the ignition switch to the LOCK position.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connectors from the curtain shield airbag assembly RH.
  4. Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire No. 2.

CAUTION: Never connect a tester to the curtain shield airbag assembly RH (Curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting. Insert the SST straight into the terminals of the connector. SST 09843-18060
  • Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  • Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  • Clear the DTCs stored in memory.
  • Turn the ignition switch to the LOCK position.
  • Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  • Check the DTCs

    • OK: DTC B1161/84 is not output.

    HINT: Codes other than DTC B1161/84 may be output at this time, but they are not related to this check.

    REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH

    2 CHECK FLOOR WIRE NO.2 (CURTAIN SHIELD SQUIB RH CIRCUIT)

    CHECK FLOOR WIRE NO.2 (CURTAIN SHIELD SQUIB RH CIRCUIT)
    1. Turn the ignition switch to the LOCK position.
    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
    3. Disconnect the SST (resistance 2.1 Ω) from the floor wire No. 2.
    4. Disconnect the connector from the center airbag sensor assembly.
    5. Measure the resistance according to the value(s) in the table below.

    Standard resistance

    Standard resistance

    3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

    CHECK CENTER AIRBAG SENSOR ASSEMBLY
    1. Connect the connectors to the curtain shield airbag assembly RH and the center airbag sensor assembly.
    2. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds
    3. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
    4. Clear the DTCs stored in memory.
    5. Turn the ignition switch to the LOCK position.
    6. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
    7. Check the DTCs.

    OK: DTC B1161/84 is not output.

    HINT: Codes other than DTC B1161/84 may be output at this time, but they are not related to this check.

    USE SIMULATION METHOD TO CHECK

    Test yourself

    A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.