Toyota Sienna Quiz
Supplemental restraint system

Short to B+ in Driver Side Squib 2nd Step Circuit

In this manual: Supplemental restraint system
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
26steps
~161min
5/5difficulty
1special tools
Done 0 of 26

DTC B1183/22 Short to B+ in Driver Side Squib 2nd Step Circuit

DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1183/22 is recorded when a short to B+ is detected in the driver side squib 2nd step circuit.

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

  • Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester.
  • After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)

CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)
  1. Turn the ignition switch to the LOCK position.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds
  3. Disconnect the connectors from the steering pad.
  4. Connect the white wire side of SST (resistance 2.1 Ω) to the spiral cable.

CAUTION: Never connect a tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting. Insert the SST straight into the terminals of the connector. SST 09843-18060
  • Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  • Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  • Clear the DTCs stored in memory.
  • Turn the ignition switch to the LOCK position.
  • Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  • Check the DTCs.

    • OK: DTC B1183/22 is not output.

    HINT: Codes other than DTC B1183/22 may be output at this time, but they are not related to this check.

    REPLACE STEERING PAD

    2 CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

    CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
    1. Turn the ignition switch to the LOCK position.
    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
    3. Disconnect the SST (resistance 2.1 Ω) from the spiral cable.
    4. Disconnect the connector from the center airbag sensor assembly.
    5. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
    6. Turn the ignition switch to the ON position.
    7. Measure the voltage according to the value(s) in the table below.

    Standard voltage

    Standard voltage

    3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

    CHECK CENTER AIRBAG SENSOR ASSEMBLY
    1. Turn the ignition switch to the LOCK position.
    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
    3. Connect the connectors to the steering pad and the center airbag sensor assembly.
    4. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
    5. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
    6. Clear the DTCs stored in memory.
    7. Turn the ignition switch to the LOCK position.
    8. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
    9. Check the DTCs.

    OK: DTC B1183/22 is not output.

    HINT: Codes other than DTC B1183/22 may be output at this time, but they are not related to this check.

    USE SIMULATION METHOD TO CHECK

    4 CHECK INSTRUMENT PANEL WIRE

    CHECK INSTRUMENT PANEL WIRE
    1. Turn the ignition switch to the LOCK position.
    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
    3. Disconnect the instrument panel wire connector from the spiral cable.
    4. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
    5. Turn the ignition switch to the ON position.
    6. Measure the voltage according to the value(s) in the table below.

    Standard voltage

    Standard voltage

    5 CHECK SPIRAL CABLE

    CHECK SPIRAL CABLE
    1. Measure the voltage according to the value(s) in the table below.

    Standard voltage

    Standard voltage

    USE SIMULATION METHOD TO CHECK

    Test yourself

    A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.