Toyota Sienna Quiz
Engine hood / door

Power Slide Door Warning Buzzer RH does not Sound

In this manual: Engine hood / door
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
4steps
~24min
2/5difficulty
Done 0 of 4

DESCRIPTION

  • The power slide door system uses warning buzzers built into RH slide doors respectively. Each buzzer has 2 ways of sounding that are used differently according to the situations:
  1. When all the following conditions are met, the warning buzzer sounds at a cycle of 0.3 seconds:

* The ignition switch is turned ON.

* The shift lever is moved into any position except P position.

* The slide door is open or the power slide door is activated to open.

The warning buzzer continues to sound until the slide door is fully closed or the shift lever is moved into the P position.

  1. While the power slide door is operating, the warning buzzer that notifies that the door is moving sounds at a cycle of 0.7 seconds. This stops sounding when the power slide door stops. This way of sounding is set to OFF at factory (default setting) and can be customized when required.
  • The power slide door ECU RH directly sends a signal to the warning buzzer.

HINT:

  • Only item 2 can be customized.
  • If both items occur at the same time, item 1 is prior to the other.

WIRING DIAGRAM

INSPECTION PROCEDURE

1 PERFORM ACTIVE TEST BY INTELLIGENT TESTER

  1. Select the ACTIVE TEST and then check that the power slide door warning buzzer RH operates.

HINT: During the ACTIVE TEST, the intelligent tester sends a signal to the power slide door ECU RH to activate the warning buzzer. If the warning buzzer is activated, the warning buzzer itself and the wire harness between the warning buzzer and power slide door ECU RH are considered to be functioning normally.

OK (Power slide door ECU RH):

Power slide door ECU RH

2 CHECK WIRE HARNESS (POWER SLIDE DOOR WARNING BUZZER RH - BODY GROUND)

CHECK WIRE HARNESS
  1. Remove the buzzer connector.
  2. Inspect the buzzer connector side voltage.
    CHECK WIRE HARNESS

NOTICE: Use an oscilloscope to check the output voltages of the buzzer

Voltage

Voltage

3 INSPECT POWER SLIDE DOOR WARNING BUZZER RH

INSPECT POWER SLIDE DOOR WARNING BUZZER RH
  1. Check the resistance of the buzzer.

Resistance

Resistance

NOTICE:

  • The circuit that causes the buzzer to sounds is built into the slide door ECU, not around the buzzer.
  • Directly applying battery voltage to the buzzer does not cause the buzzer to sound.

4 CHECK WIRE HARNESS (POWER SLIDE DOOR WARNING BUZZER RH - POWER SLIDE DOOR ECU RH)

CHECK WIRE HARNESS
  1. Disconnect the P34 buzzer and the P27 ECU connectors.
  2. Check the resistance between the wire harness side connectors.

Resistance (Check for open circuit)

REPLACE POWER SLIDE DOOR ECU RH

Test yourself

A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.