Toyota Tacoma Quiz
Rc62f Manual Transmission / Transaxle

How To Proceed With Troubleshooting

In this manual: Rc62f Manual Transmission / Transaxle
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~1min read
CAUTION / NOTICE / HINT

HINT:

  • Use the following procedure to troubleshoot the manual transaxle system.

    *: Use the Techstream.

PROCEDURE

  1. VEHICLE BROUGHT TO WORKSHOP

NEXT

  1. CUSTOMER PROBLEM ANALYSIS

(a) Refer to the How to Troubleshoot ECU Controlled Systems in Introduction section.

Click here

NEXT

  1. INSPECT BATTERY VOLTAGE

(a) Measure the battery voltage.

Standard Voltage:

11 to 14 V

HINT:

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

NEXT

  1. CHECK CAN COMMUNICATION SYSTEM*

(a) Using the Techstream, check if the CAN communication system is functioning normally.

HINT:

  • Refer to CAN Bus Check in CAN Communication System.

    Click here

  • The ECM is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there are no malfunctions in the CAN communications system.

Result

Proceed to

CAN communication system DTCs are not output.

A

CAN communication system DTCs are output.

B
B

GO TO CAN COMMUNICATION SYSTEM
A

  1. CHECK AND CLEAR DTCS AND FREEZE FRAME DATA*

(a) Refer to DTC Check/Clear.

Click here

NEXT

  1. SELECT CHECK MODE DIAGNOSIS*

(a) Refer to Check Mode Procedure.

Click here

NEXT

  1. CHECK FOR DTC*

(a) Proceed to DTC Check/Clear.

Click here

Result

Proceed to

DTCs are not output.

A

DTCs are output.

B
B

GO TO STEP 12
A

  1. SYMPTOM SIMULATION

(a) Refer to Symptom Simulation.

Click here

NEXT

  1. COMPONENT INSPECTION

NEXT

  1. REPAIR OR REPLACE

NEXT

  1. CONFIRMATION TEST

NEXT

END

  1. DIAGNOSTIC TROUBLE CODE CHART

(a) Proceed to Diagnostic Trouble Code Chart.

Click here

NEXT

  1. CIRCUIT INSPECTION*

NEXT

  1. IDENTIFICATION OF PROBLEM

NEXT

  1. REPAIR OR REPLACE

NEXT

  1. CONFIRMATION TEST

NEXT

END

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.