DESCRIPTION
When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.
WIRING DIAGRAM
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
PERFORM ACTIVE TEST USING TECHSTREAM (Security Horn)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Active Test.
(e) According to the display on the Techstream, perform the Active Test. Main Body
Tester Display | Test Part | Control Range | Diagnostic Note |
Security Horn |
Security horn assembly |
ON/OFF |
- |
OK:
The security horn assembly sounds and stops correctly when operated through the Techstream.
| OK |
 |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG |
 |
|
INSPECT SECURITY HORN ASSEMBLY
(a) Remove the security horn assembly.
Click here 
(b) Inspect the security horn assembly.
Click here 
| NG |
 |
REPLACE SECURITY HORN ASSEMBLY |
| OK |
 |
|
INSPECT SECURITY HORN RELAY
(a) Remove the SECURITY HORN relay. |
 |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
3 - 5 |
Battery voltage is applied between terminals 2 - 1 |
Below 1 Ω |
3 - 5 |
Battery voltage is not applied between terminals 2 - 1 |
10 kΩ or higher |
| NG |
 |
REPLACE SECURITY WARNING RELAY (S-HORN RELAY) |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
(a) Remove the main body ECU (multiplex network body ECU).
Click here 
(b) Connect the driver side junction block assembly connectors.
(c) Remove the SECURITY HORN relay.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
2 - A-29 (SH) |
Always |
Below 1 Ω |
2 - Body ground |
Always |
10 kΩ or higher |
2 or A-29 (SH) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG |
 |
GO TO STEP 7 |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (BATTERY - SECURITY HORN RELAY)
(a) Remove the SECURITY HORN relay. |
 |
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
1 - Body ground |
Always |
11 to 14 V |
3 - Body ground |
Always |
11 to 14 V |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - SECURITY HORN ASSEMBLY AND BODY GROUND)
(a) Remove the SECURITY HORN relay.
(b) Disconnect the A28 security horn assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
5 - A28-1 |
Always |
Below 1 Ω |
5 or A28-1 - Other terminals and body ground |
Always |
10 kΩ or higher |
| OK |
 |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
(a) Disconnect the 3H driver side junction block assembly connector.
(b) Remove the SECURITY HORN relay.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
2 - 3H-26 |
Always |
Below 1 Ω |
2 - Body ground |
Always |
10 kΩ or higher |
2 or 3H-26 - Other terminals and body ground |
Always |
10 kΩ or higher |
| OK |
 |
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|