Based on dynamic radar cruise control system operation, the forward recognition camera provides warnings to the driver by sounding the skid control buzzer assembly.
DTC C1A4A is stored when a malfunction is detected in the skid control buzzer assembly circuit.
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
C1A4A
Skid Control Buzzer Circuit
While the vehicle speed is 36 km/h or more and the dynamic radar cruise control system is operating, the forward recognition camera detects a malfunction in the skid control buzzer assembly circuit for approximately 0.4 seconds or more.
Skid control buzzer assembly
Millimeter wave radar sensor assembly
Forward recognition camera
Harness or connector
WIRING DIAGRAM
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the forward recognition camera, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle, and as a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.
Click here
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.
Click here
PROCEDURE
CHECK FOR DTCs (PRE-COLLISION SYSTEM)
(a) Check for DTCs of the pre-collision system.
Click here
HINT:
The dynamic radar cruise control system only stores DTC C1A4A when the vehicle speed reaches 36 km/h, however the pre-collision system stores this DTC at any vehicle speed. If DTC C1A4A is stored by the pre-collision system, perform troubleshooting of the pre-collision system first.
Result
Proceed to
DTC C1A4A is not output
A
DTC C1A4A is output
B
B
GO TO PRE-COLLISION SYSTEM
A
CHECK FOR DTCs (RADAR CRUISE 2)
(a) Clear the DTCs.
Click here
(b) Make sure that the DTC detection conditions are met.
HINT:
If the detection conditions are not met, the system cannot detect the malfunction.
Turn the ignition switch to ON.
Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).
Drive the vehicle at 36 km/h or more for 1 second or more.
(c) Perform the Active Test according to the display on the Techstream.
Click here
NOTICE:
Perform the Active Test for 1 second or more.
HINT:
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
Powertrain > Radar Cruise2 > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Radar Cruise Stop Buzzer
Skid control buzzer assembly (stop sound)
ON or OFF
Buzzer can be heard
Radar Cruise Approach Alarm Buzzer
Skid control buzzer assembly (approach sound)
ON or OFF
Buzzer can be heard
(d) Check for DTCs.
Click here
Result
Proceed to
DTC C1A4A is not output
A
DTC C1A4A is output
B
A
USE SIMULATION METHOD TO CHECK
B
INSPECT TERMINAL VOLTAGE
(a) Disconnect the J167 skid control buzzer assembly connector.
*a
Front view of wire harness connector
(to Skid Control Buzzer Assembly)
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Condition
Specified Condition
J167-2 (IG1) - Body ground
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - BATTERY)
OK
CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - FORWARD RECOGNITION CAMERA)
(a) Disconnect the J167 skid control buzzer assembly connector.
(b) Disconnect the W9 forward recognition camera connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
J167-1 (BZ) - W9-8 (BZ)
Always
Below 1 Ω
J167-1 (BZ) or W9-8 (BZ) - Body ground
Always
10 kΩ or higher
OK
GO TO STEP 7
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - FORWARD RECOGNITION CAMERA)
(a) Repair or replace the harness or connector.
NEXT
CHECK FOR DTCs (RADAR CRUISE 2)
(a) Clear the DTCs.
Click here
(b) Perform the Active Test according to the display on the Techstream.
Click here
NOTICE:
Perform the Active Test for 1 second or more.
HINT:
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
Powertrain > Radar Cruise2 > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Radar Cruise Stop Buzzer
Skid control buzzer assembly (stop sound)
ON or OFF
Buzzer can be heard
Radar Cruise Approach Alarm Buzzer
Skid control buzzer assembly (approach sound)
ON or OFF
Buzzer can be heard
(c) Check for DTCs.
Click here
Result
Proceed to
DTC C1A4A is not output
A
DTC C1A4A is output
B
A
END
B
INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)
(a) Turn the ignition switch to ON.
(b) Check if the skid control buzzer assembly is sounding.
Result
Proceed to
The skid control buzzer assembly does not sound when the ignition switch is ON
A
The skid control buzzer assembly sounds continuously when the ignition switch is ON
B
B
GO TO STEP 9
A
INSPECT SKID CONTROL BUZZER ASSEMBLY (UNIT INSPECTION)
(a) Remove the skid control buzzer assembly.
Click here
(b) Inspect the skid control buzzer assembly.
Click here
Result
Proceed to
Skid control buzzer assembly is abnormal
A
Skid control buzzer assembly is normal
B
B
GO TO STEP 10
A
REPLACE SKID CONTROL BUZZER ASSEMBLY
(a) Replace the skid control buzzer assembly.
Click here
NEXT
CHECK FOR DTCs (RADAR CRUISE 2)
(a) Clear the DTCs.
Click here
(b) Perform the Active Test according to the display on the Techstream.
Click here
NOTICE:
Perform the Active Test for 1 second or more.
HINT:
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
Powertrain > Radar Cruise2 > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Radar Cruise Stop Buzzer
Skid control buzzer assembly (stop sound)
ON or OFF
Buzzer can be heard
Radar Cruise Approach Alarm Buzzer
Skid control buzzer assembly (approach sound)
ON or OFF
Buzzer can be heard
(c) Check for DTCs.
Click here
Result
Proceed to
DTC C1A4A is not output
A
DTC C1A4A is output
B
A
END
B
REPLACE FORWARD RECOGNITION CAMERA
(a) Replace the forward recognition camera.
Click here
(b) Perform forward recognition axis adjustment.
Click here
NEXT
CHECK FOR DTCs (RADAR CRUISE 2)
(a) Clear the DTCs.
Click here
(b) Perform the Active Test according to the display on the Techstream.
Click here
NOTICE:
Perform the Active Test for 1 second or more.
HINT:
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
Powertrain > Radar Cruise2 > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Radar Cruise Stop Buzzer
Skid control buzzer assembly (stop sound)
ON or OFF
Buzzer can be heard
Radar Cruise Approach Alarm Buzzer
Skid control buzzer assembly (approach sound)
ON or OFF
Buzzer can be heard
(c) Check for DTCs.
Click here
Result
Proceed to
DTC C1A4A is not output
A
DTC C1A4A is output
B
A
END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)
B
REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
(a) Replace the millimeter wave radar sensor assembly.
Click here
(b) Adjust the millimeter wave radar sensor assembly.
Click here
NEXT
CLEAR DTC (RADAR CRUISE 2)
(a) Clear the DTCs.
Click here
NEXT
END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)