Toyota Venza Quiz
1ar-fe Engine Control

Accelerator Pedal

In this manual: 1ar-fe Engine Control
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
010203040505.44N·mlb·ft
Tightening torque found on this page
Components COMPONENTS ILLUSTRATION
On-vehicle Inspection ON-VEHICLE INSPECTION PROCEDURE

1. INSPECT ACCELERATOR PEDAL SENSOR ASSEMBLY

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

(e) Read the values displayed on the Techstream.

Standard Voltage:

Tester Display

Condition

Specified Condition

Accel Sensor Out No. 1

Accelerator pedal is released

0.5 to 1.1 V

Accelerator pedal is fully depressed

2.6 to 4.5 V

Accel Sensor Out No. 2

Accelerator pedal is released

1.2 to 2.0 V

Accelerator pedal is fully depressed

3.4 to 4.75 V

If the result is not as specified, check the accelerator pedal sensor assembly, wire harness or ECM.

Installation INSTALLATION PROCEDURE

1. INSTALL ACCELERATOR PEDAL SENSOR ASSEMBLY

NOTICE:

  • Avoid physical shock to the accelerator pedal sensor assembly.
  • Do not disassemble the accelerator pedal sensor assembly.
  • The accelerator pedal sensor assembly does not require lubrication.
  • Do not apply oil or other lubricants to the accelerator pedal sensor assembly. If applied, the accelerator pedal sensor assembly must be replaced.

(a) Install the accelerator pedal sensor assembly with the 2 bolts.

Torque:

5,4 N·m {55 kgf·cm, 48 in·lbf}

(b) Connect the accelerator pedal sensor assembly connector.

Removal REMOVAL PROCEDURE

1. REMOVE ACCELERATOR PEDAL SENSOR ASSEMBLY

NOTICE:

  • Avoid physical shock to the accelerator pedal sensor assembly.
  • Do not disassemble the accelerator pedal sensor assembly.
  • The accelerator pedal sensor assembly does not require lubrication.
  • Do not apply oil or other lubricants to the accelerator pedal sensor assembly. If applied, the accelerator pedal sensor assembly must be replaced.

(a) Disconnect the accelerator pedal sensor assembly connector.

(b) Remove the 2 bolts and accelerator pedal sensor assembly.

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.