Toyota Venza Quiz
Power Assist Systems

Torque Sensor Zero Point Adjustment Undone (C1515,C1525)

In this manual: Power Assist Systems
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
DESCRIPTION

These DTCs do not indicate a malfunction. The power steering ECU stores these DTCs when it determines that the rotation angle sensor value initialization and torque sensor zero point calibration have not been performed.

DTC No.

DTC Detection Condition

Trouble Area

C1515

This DTC is detected when torque sensor zero point calibration has not been performed.

There is no malfunction if this DTC is not output again after performing torque sensor zero point calibration.

C1525

This DTC is detected when rotation angle sensor value initialization has not been performed.

There is no malfunction if this DTC is not output again after performing rotation angle sensor value initialization.
CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU and steering column assembly have been replaced, perform the rotation angle sensor initialization and torque sensor zero point calibration (See page ).


PROCEDURE

  1. INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT

(a) Initialize the rotation angle sensor value and calibrate the torque sensor zero point (See page ).


NEXT

  1. CHECK FOR DTC

(a) Check for DTCs (See page ).


Condition

Proceed to

DTC C1515 or C1525 is still output after performing rotation angle sensor value initialization and torque sensor zero point calibration 3 times.

A

DTC C1515 or C1525 is not output.

B

NOTICE:

If DTC C1515 or C1525 is output even though the rotation angle sensor value initialization and torque sensor zero point calibration have been performed, confirm the procedure again, and perform the calibration and initialization 3 times.

HINT:

Replace the power steering ECU if DTC C1515 or C1525 is still output after performing rotation angle sensor value initialization and torque sensor zero point calibration 3 times.


B

END
A

  1. REPLACE POWER STEERING ECU

(a) Replace the power steering ECU (See page ).


NEXT

  1. INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT

(a) Initialize the rotation angle sensor value and calibrate the torque sensor zero point (See page ).


NEXT

  1. CHECK FOR DTC

(a) Check for DTCs (See page ).


Condition

Proceed to

DTC C1515 or C1525 is still output after performing rotation angle sensor value initialization and torque sensor zero point calibration 3 times.

A

DTC C1515 or C1525 is not output.

B

NOTICE:

If DTC C1515 or C1525 is output even though the rotation angle sensor value initialization and torque sensor zero point calibration have been performed, confirm the procedure again, and perform the calibration and initialization 3 times.

HINT:

Replace the power steering gear if DTC C1515 or C1525 is still output after performing rotation angle sensor value initialization and torque sensor zero point calibration 3 times.


A

REPLACE STEERING COLUMN ASSEMBLY

B

END

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.