Electrical system

Relay carrier, fuse carrier, E-boxes

~5min read

Removing and installing E-box

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque wrench -V.A.G 1410-

Caution!

When disconnecting and connecting the battery, follow the procedure described in the repair manual.

Removing

- Switch off ignition and all electrical consumers and remove the ignition key.

- Disconnect battery.

VW UP. Elektrische Anlage

- Release the catches -arrows- and remove the cover of the E-box -1-.

- Note the terminal assignment of the E-box.


Caution!
  • Electrical components protected by the multi-fuse may fail!
  • Loosening the nuts for the wire connections will damage the multi-fuse!
  • The multi-fuse must be replaced after each loosening of the connections!
VW UP. Elektrische Anlage

- Unscrew all nuts of the wire connections -arrows A- and remove the wires from the connection studs.

- Unscrew nut -arrow B-.

- Unlock the catches -arrows C- of the E-box holder on both sides and lift the E-box together with the holder off the battery upward.

VW UP. Elektrische Anlage

- Turn the E-box holder over, release the catch -arrow- and remove the E-box from the E-box holder.

VW UP. Elektrische Anlage

- Release the latch -arrow- and pull the fuse holder -1- upward off the E-box.

- Remove the E-box from the vehicle.

Installing

Installation is carried out in the reverse order of removal, observing the following:

VW UP. Elektrische Anlage

- Install a new multi-fuse and tighten the nuts -arrows A- and -arrow B-.

- Connect battery.

VW UP. Elektrische Anlage

Tightening torques


Remove and install relay and fuse holder in E-box

The fuse holder in the E-box is attached to the side of the E-box on the battery.

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque wrench -V.A.G 1410-
VW UP. Elektrische Anlage

  • Release tool set -VAS 1978/35-

Caution!

When disconnecting and connecting the battery, follow the procedure described in the repair manual.

Removing

- Switch off ignition and all electrical consumers and remove the ignition key.

- Disconnect battery.

- Remove the E-box from the battery.


Caution!
  • Electrical components protected by the multi-fuse may fail!
  • Loosening the nuts for the wire connections will damage the multi-fuse!
  • The multi-fuse must be replaced after each loosening of the connections!
VW UP. Elektrische Anlage

- Unscrew the 2 nuts -arrows- and remove the power busbar -1- and the multi-fuse -2- from the E-box.

VW UP. Elektrische Anlage

- Turn the E-box over, release the latch -arrow- and pull the fuse holder -1- upward off the E-box.

VW UP. Elektrische Anlage

- Press the side latches -arrows- and remove the cover of the fuse holder -1-.

- Note the fuse assignment and pull all fuses out of the fuse holder.

VW UP. Elektrische Anlage

- Pull the primary lock -1- in the -arrow direction-, release all connector contacts with the correct release tool from release tool set -VAS 1978/35- and pull them downward out of the fuse holder.


Note

The correct release tool can be found in the table in the → Operating instructions for VAS 1978/35.

Installing

Installation is carried out in the reverse order of removal, observing the following:

VW UP. Elektrische Anlage

- Install a new multi-fuse -2- and tighten the nuts -arrows-.

- Connect battery.

VW UP. Elektrische Anlage

Tightening torques


Remove and install relay and fuse carrier behind driver-side instrument panel

Remove and install fuse carrier behind driver-side instrument panel

The fuse carrier is located behind the side instrument panel cover.

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque wrench -V.A.G 1410-

Caution!

When disconnecting and connecting the battery, follow the procedure described in the repair manual.


Note
  • The illustrations show the removal and installation of the fuse holder on a left-hand drive vehicle.
  • Removal and installation of the fuse holder on a right-hand drive vehicle is performed accordingly.

Removing

- Switch off ignition and all electrical consumers and remove the ignition key.

- Disconnect battery.

VW UP. Elektrische Anlage

- Insert the removal wedge -VAS 3409- or a screwdriver into the recess -2- and pry the instrument panel cover -1- off in the -arrow direction-.

VW UP. Elektrische Anlage

- Unscrew the mounting screw -arrow- and pull the fuse holder -1- together with the carrier -2- upward off the body shell.

Installing

Installation is carried out in the reverse order of removal, observing the following:

VW UP. Elektrische Anlage

Tightening torques


Remove and install fuse carrier on relay carrier

The fuse carrier is located behind the panel in the driver's footwell below the relay carrier.

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque wrench -V.A.G 1410-
VW UP. Elektrische Anlage

  • Release tool set -VAS 1978/35-

Caution!

When disconnecting and connecting the battery, follow the procedure described in the repair manual.


Note
  • The illustrations show the removal and installation of the fuse carrier on a left-hand drive vehicle.
  • Removal and installation of the fuse carrier on a right-hand drive vehicle is performed accordingly.

Removing

- Switch off ignition and all electrical consumers and remove the ignition key.

- Disconnect battery.

- Remove the panel in the driver's footwell → Body Assembly Work Interior.

- Remove the lower A-pillar trim on the driver's side → Body Assembly Work Interior.

VW UP. Elektrische Anlage

- Unscrew the mounting screws -arrows- and pull the fuse carrier -1- out of the relay carrier, taking into account the connected cable lengths.

- Note the fuse assignment and pull all fuses out of the fuse carrier.

VW UP. Elektrische Anlage

- Pull the primary locks -1-, release all connector contacts with the correct release tool from release tool set -VAS 1978/35- and pull them rearward out of the fuse carrier.


Note

The correct release tool can be found in the table in the → Operating instructions for VAS 1978/35.

Installing

Installation is carried out in the reverse order of removal, observing the following:

VW UP. Elektrische Anlage

Tightening torques


Remove and install instrument panel relay carrier

The instrument panel relay carrier is installed in the driver's footwell below the instrument panel.

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque wrench -V.A.G 1410-
VW UP. Elektrische Anlage

  • Release tool set -VAS 1978/35-

Caution!

When disconnecting and connecting the battery, follow the procedure described in the repair manual.


Note
  • The illustrations show the removal and installation of the relay carrier on a left-hand drive vehicle.
  • Removal and installation of the relay carrier on a right-hand drive vehicle is performed accordingly.

Removing

- Switch off ignition and all electrical consumers and remove the ignition key.

- Disconnect battery.

- Remove the panel in the driver's footwell → Body Assembly Work Interior.

- Remove the lower A-pillar trim on the driver's side → Body Assembly Work Interior.

- Remove the fuse holder from the relay carrier.

- Remove the onboard supply control unit -J519-.


Note

For clarity, the relay carrier is shown from the rear in the following illustration.

VW UP. Elektrische Anlage

- Unscrew the 3 mounting nuts (wrench size 10 mm) -arrows- and lift the relay carrier -1- off the threaded studs, taking into account the connected cable lengths.

VW UP. Elektrische Anlage

- Cut the cable tie -arrow- and unclip the wire harness retainer -1- from the relay carrier.

- Note the relay assignment in the holder.

VW UP. Elektrische Anlage

- Release all relay connectors on the rear of the relay carrier -arrows- and pull them rearward out of the relay carrier together with the inserted relays.

VW UP. Elektrische Anlage

- Release the diagnostic connector -1- -arrow- and pull it out of the relay carrier -2-.

- Remove the relay carrier -2- from the vehicle.

Installing

Installation is carried out in the reverse order of removal, observing the following:


Note

Secure all cable ties and wire harness retainers that were detached during removal back to their original positions.

VW UP. Elektrische Anlage

Tightening torques