Door
Assembly overview - Door
Assembly overview - Door hinges
![]()
Note
- The illustration shows the left side. The right side is handled in the same way.
- Always replace the door hinge bolts after loosening them.

- Front door
- Remove and install
- adjust
- Bolt
- Always replace. Loosening once for door adjustment is permitted.
- Tightening torque: 50 N·m
- After replacing the A-pillar, a different tightening torque must be observed.
- Tightening torque after replacing the A-pillar: 20 N·m + 90°
- Door hinge
- Hinge is split.
- The lower part is connected to the upper hinge part by bolt -5-.
- Bolt
- Always replace. Loosening once for door adjustment is permitted.
- Tightening torque: 50 N·m
- installed from the vehicle interior
- For removal and installation, the lower A-pillar trim must be removed → Body Assembly Work Interior
- After replacing the A-pillar, a different tightening torque must be observed.
- Tightening torque after replacing the A-pillar: 20 N·m + 90°
- Bolt
- connects upper hinge part -3- with lower hinge part -6-
- Tightening torque: 23 N·m
- Door hinge
- The hinge is split.
- The upper part is connected to the lower hinge part by bolt -5-.
- Bolt
- Always replace. Loosening once for door adjustment is permitted.
- Tightening torque: 50 N·m
- Bolt
- Tightening torque: 30 N·m
- Door check strap
- Remove and install
- Bolt
- 2 pieces
- Tightening torque: 9 N·m
- Door hinge
- The hinge is split.
- The upper part is connected to the lower hinge part by bolt -16-.
- Bolt
- Always replace. Loosening once for door adjustment is permitted.
- Tightening torque: 50 N·m
- Bolt
- Always replace. Loosening once for door adjustment is permitted.
- Tightening torque: 50 N·m
- After replacing the A-pillar, a different tightening torque must be observed.
- Tightening torque after replacing the A-pillar: 20 N·m + 90°
- Door hinge
- Hinge is split.
- The lower part is connected to the upper hinge part by bolt -16-.
- Bolt
- Always replace. Loosening once for door adjustment is permitted.
- Tightening torque: 50 N·m
- installed from the vehicle interior
- For removal and installation, the instrument panel must be removed → Body Assembly Work Interior
- After replacing the A-pillar, a different tightening torque must be observed.
- Tightening torque after replacing the A-pillar: 20 N·m + 90°
- Bolt
- connects upper hinge part -3- with lower hinge part -6-
- Tightening torque: 23 N·m
Removing and installing the door
Required Special Tools, Test and Measuring Equipment and Auxiliary Items
- Key for door adjustment -3320-
- Joint for 3320 -3320/1-
- Bit insert for 3320 -3320/2-
- Bit insert for 3320 -3320/3-
- Torque Wrench -V.A.G 1331-
- Socket insert -3410-
- Adjustment gauge -3371-
- Release Wedge -3409-
![]()
Note
Removal and installation are described for the left front door only. Removal and installation of the right front door are carried out in the same way.
Removing


Carry out the following work:
- Release bellows -2- by pressing the detent -arrow a- and pull them off the A-pillar.
- Swing locking lever -3- downward -arrow b- and disconnect electrical connector -4- from the coupling station.
- Loosen bolts -7- on the hinges.
- Unscrew bolt -5- for door check strap -6-.
- Push door check strap -6- inward -arrow c-.
- Lift front door -1- with hinges -9- upward -arrow e- off hinges -8-.
Installing

Carry out the following work:
Installation is carried out in the reverse order. Observe the following:
![]()
Caution!
Before hanging the front door, the bearing of the door check strap must be folded toward the vehicle interior (to avoid paint damage).
Tightening torque for bolts -5-: 30 N·m.
Tightening torque for bolts -7-: 23 N·m.
![]()
Note
After hanging the front door, the hinge leaves must lie flush against each other.
- Adjust front door -1-.
- Observe gap dimensions of front door -1-.
Installation after replacing the A-pillar
![]()
Note
Installation after replacing the A-pillar is described for the left front door only. Installation after replacing the A-pillar on the right front door is carried out in the same way.
![]()
WARNING!
If the A-pillar has been replaced, be sure to tighten the bolts on the A-pillar as follows.

Carry out the following work:
- A-pillar has been replaced.
- Always replace the bolts. Loosening them once for door adjustment is permitted.
Installation is carried out in the reverse order. Observe the following:
- Fit front door -1- and tighten bolts -2-, -3-, -6- and -7-. Tightening torque: 20 N·m + 90º.
Tightening torque for bolts -2-: 20 N·m + 90º.
Tightening torque, bolts -4-: 23 N·m.
- Adjust front door.
- Observe gap dimensions of front door.
Adjusting the door
Required Special Tools, Test and Measuring Equipment and Auxiliary Items
- Key for door adjustment -3320-
- Joint for 3320 -3320/1-
- Bit insert for 3320 -3320/2-
- Bit insert for 3320 -3320/3-
- Torque Wrench -V.A.G 1331-
- Socket insert -3410-
- Adjustment gauge -3371-
- Release Wedge -3409-

![]()
Note
- Adjustment is described for the left front door only. The right front door is adjusted in the same way.
- To adjust the front door, the vehicle must be standing on its wheels.
- The front door is correctly adjusted when the gap is even all around in the closed state, the door does not sit too far inward or outward, and the contours are flush.
- For checking the gap dimensions.
- After installation or adjustment work, apply corrosion protection to the hinges and bolts.

Carry out the following work:
Adjusting the gap dimensions
For correct adjustment of the gap dimensions, loosen bolts -2-, -3-, -6- and -7- on the A-pillar.
- To loosen bolt -7-, the instrument panel must be removed → Body assembly work interior.
- To loosen bolt -3-, the lower A-pillar trim must be removed → Body assembly work interior.
Adjusting the flush alignment
For correct adjustment of the flush alignment, loosen bolts -5- and -9-.
Use special tool door adjustment wrench -3320- with the corresponding bit insert for this.
![]()
Note
Other measures, such as raising the front door upward, are ineffective. If the door is pressed down afterward, the front door will sag again.
Adjusting the striker.
Adjusting adjustment buffers

Adjusting adjustment buffers
- The adjusting buffer -1- is set by turning it.
Protective film
- Check protective film -3- for damage and replace if necessary.
- Cut protective film -3- yourself from film sheet -AKL 448 300 04-.
Dimensions:
- Ø 22 mm
- Dimension -a- from the edge of the grommet to the center of the film is 165 mm.
- Dimension -b- from the upper edge of the rocker panel to the center of the film is 14 mm.
Grommet
- Check grommet -2- for damage and replace if necessary.
Adjusting the striker
Required Special Tools, Test and Measuring Equipment and Auxiliary Items
- Torque Wrench -V.A.G 1331-

- Socket insert -3410-

![]()
Note
- The threaded plate -1- of the striker is attached to the pillar differently than previously known.
- The bracket outside the threaded plate is welded firmly to the pillar. The webs to the threaded plate are plastically deformable.
- To adjust striker -2- with bolts -3- loosened, considerable force must be applied.

![]()
Note
- Adjustment is described for the left front door only. The right front door is adjusted in the same way.
- When closing, the front door must lock completely without additional effort and must have no play.
- Adjusting the striker must not press the front door upward or downward.
The striker can be used to adjust the alignment of the front door to the side panel or to the rear door -arrows a- and -arrows b- (wind noise).
Carry out the following work:
- Loosen striker -1- by loosening bolts -2- on the B-pillar.
![]()
Note
To adjust striker -1- with bolts -2- loosened, considerable force must be applied.
- Tighten bolts -2- of striker -1-.
Tightening torque bolts -2-: 20 N·m.