Tire Repair Kit

Minor damage to the tire tread and sidewall can be repaired using the tire repair kit.

Do not remove foreign objects from the tire.

The tire repair kit cannot repair damage larger than 4 mm or located close to the rim.

Do not exceed a speed of 80 km/h.

Do not drive on the repaired tire for an extended period.

Vehicle handling and ride quality may deteriorate.

If the tire is flat:

Apply the parking brake, shift into first gear, reverse, or move the shift lever to P.

The tire repair kit is stored in the compartment under the floor mat in the luggage compartment.

1. Remove the tire repair kit from the compartment.

2. Remove the compressor.

3. Remove the power cord and air hose from their storage compartments under the compressor.

4. Screw the compressor air hose onto the sealant bottle fitting.

5. Secure the sealant bottle to the compressor holder.

Place the compressor next to the tire so that the sealant bottle is in a vertical position.

6. Unscrew the valve cap of the damaged tire.

7. Screw the free end of the hose onto the tire valve.

8. Set the compressor switch to the position.

9. Insert the compressor power plug into the auxiliary power outlet behind the console.

To prevent battery discharge, it is recommended to start the engine.

10. Set the compressor switch to position I. The tire will fill with sealant.

11. If the sealant in the container runs out, the compressor gauge briefly (about 30 seconds) shows pressure up to 6 bar. Then the pressure begins to drop.

12. This means the entire sealant has been injected into the tire. Then the tire must be inflated with air.

13. The operating tire pressure will be reached in about 10 minutes. Tire pressure 184.

When the required pressure is reached, switch off the compressor.

If the specified tire pressure is not reached within 10 minutes, disconnect the tire repair kit. Move the vehicle so that the wheel makes one revolution.

Reconnect the tire repair kit and continue inflating the tire for another 10 minutes.

If the required pressure still cannot be reached, the tire is severely damaged. Contact a service station for assistance.

Release excess tire pressure using the button on the gauge.

Do not operate the compressor for more than 10 minutes.

14. Disconnect the tire repair kit. To remove the sealant bottle, press the clamp on the bracket. Screw the tire inflation hose onto the freed bottle fitting. This will keep the sealant in the bottle.

Stow the tire repair kit in the luggage compartment.

15. Wipe off the sealant that has leaked out with a rag.

16. Remove the speed limit label from the sealant bottle and affix it within the driver's field of view.

17. Drive off immediately so the sealant distributes evenly inside the tire. After approximately 10 km (6 miles) (but no later than 10 minutes), stop and check the tire pressure. To do this, screw the compressor air hose directly onto the tire valve and the compressor.

If the pressure is above 1.3 bar, adjust it to the required value. Repeat the procedure until the pressure stops dropping.

If the pressure drops below 1.3 bar, do not drive the vehicle. Contact a service station for assistance.

18. Stow the tire repair kit in the luggage compartment.

This repair noticeably reduces driving comfort, so the tire must be replaced.

If unusual noises occur or the compressor overheats, switch it off for at least 30 minutes.

The built-in safety valve opens at a pressure of 7 bar.

Check the expiration date of the kit. After the specified date, the manufacturer cannot guarantee effective puncture repair. Carefully read the storage information printed on the sealant bottle.

Replace the used sealant bottle. Dispose of the bottle in accordance with applicable legislation.

The compressor and sealant may be used at temperatures down to -30 °C.

The supplied adapters can be used to inflate balls, inflatable mattresses, inflatable boats, and similar items. They are stored in the lower part of the compressor.

To remove an adapter, screw the compressor air hose onto it and pull.