Brake Caliper Assembly
Exploded View
REMOVAL

| Brake caliper assembly | |||||
| : N·m (kg-m, ft-lb) | |||||
DISASSEMBLY

| Cap | Bleeder valve | Cylinder body | |||
| Sliding pin | Bushing | Sliding pin boot | |||
| Piston seal | Piston | Piston boot | |||
| Torque member | |||||
| : vehicle front | |||||
| : N·m (kg-m, ft-lb) | |||||
| : NISSAN rubber grease. | |||||
| : NISSAN brake fluid No.2500 | |||||
| : Always replace after every disassembly. | |||||
Removal & Installation
REMOVAL
Remove tires. Refer to ROAD WHEEL TIRE : Removal & Installation.
Perform the advance preparation "(Air release) Accumulator pressure release" using CONSULT. Refer to Work Procedure.
Fix the disc rotor using wheel nuts.
Drain brake fluid. Refer to Draining.
Remove union bolts and copper washer and then separate brake hose from brake caliper assembly. Refer to Removal and Installation.
Remove torque member mounting bolts
and then remove brake caliper assembly.

INSTALLATION
Install disc rotor.
2WD: Refer to Removal and Installation.
4WD: Refer to Removal and Installation.
Install brake caliper assembly to steering knuckle and tighten torque member mounting bolts
to the specified torque. Refer to FRONT BRAKE CALIPER ASSEMBLY : Exploded View.

Install copper washers and brake hose to brake caliper and tighten union bolt to the specified torque. Refer to Exploded View.
Perform air bleeding. Refer to Work Procedure.
Check front disc brake for dragging. Refer to Inspection and Adjustment.
Install tires. Refer to ROAD WHEEL TIRE : Removal & Installation.
Perform inspection after installation. Refer to FRONT BRAKE CALIPER ASSEMBLY : Inspection.
Disassembly & Assembly
DISASSEMBLY
Remove sliding pin bolts and then remove cylinder body from torque member.
Remove sliding pin boots from torque member.
Remove bushing
from sliding pin
.

Place a wooden block as shown in the figure, and blow air into union bolt mounting hole to remove pistons and piston boots.

Remove piston seals from cylinder body using seal pick tool.

Remove bleeder valve and cap.
Perform inspection after disassembly. Refer to FRONT BRAKE CALIPER ASSEMBLY : Inspection.
ASSEMBLY
Install bleeder valve and cap.
Apply new brake fluid to piston seals
, and install them to cylinder body.

Apply new brake fluid to piston boots
. Cover piston end
with piston boot, and then install cylinder side lip of piston boot securely into groove on cylinder body.

Apply new brake fluid to pistons
. Push piston into cylinder body and then install piston-side lip of piston boot
into the piston groove.

Apply rubber grease to mating faces
between sliding pin
and bushing
, and install bushing to sliding pin.

Apply rubber grease to mating faces
between sliding pins
and sliding pin boots
, and install sliding pins and sliding pin boots to torque member
.

Install cylinder body to torque member and tighten sliding pin bolts to the specified torque. Refer to FRONT BRAKE CALIPER ASSEMBLY : Exploded View.
Inspection
INSPECTION AFTER DISASSEMBLY
Check the following items and replace if necessary.
Cylinder Body
Check cylinder inner wall for rust, wear, cracks or damage.
Torque Member
Check the torque member for rust, wear, cracks or damage.
Pistons
Check surface of piston for rust, wear, cracks or damage.
Sliding Pin, Sliding Pin Boot and Bushing
Check sliding pins, sliding pin boots and bushing for rust, wear, cracks or damage.
INSPECTION AFTER INSTALLATION
Check front disc brake for dragging. If any drag is found, follow the procedure described below.
Remove brake pads. Refer to Removal and Installation.
Return pistons caliper.
Install brake pad. Refer to Removal and Installation.
Depress the brake pedal several times.
Check front disc brake for dragging again. When any drag is found, disassemble the cylinder body and replace if necessary. Refer to FRONT BRAKE CALIPER ASSEMBLY : Disassembly & Assembly.
If brake pads are replaced or ground, or if braking force is felt strange, perform break-in work. Refer to Inspection and Adjustment.