Engine

Engine Coolant

~8min read

Inspection

LEVEL

  • Check if the reservoir tank engine coolant level is within the “MIN” to “MAX” when the engine is cool.

    : MAX
    : MIN
  • Adjust the engine coolant level if necessary.

LEAKAGE

A small amount of engine coolant is discharged from the lubrication surface during normal operation and may be found as a coolant residue on the plug, bleed hole, or bottom of water pump assembly.

In case of coolant residue is found on the water pump assembly, check the water pump leakage. Refer to WATER PUMP : Inspection.

  • Open the reservoir tank cap.

    : Radiator cap
    : Reservoir tank cap
  • To check for leakage, apply pressure to the cooling system with the radiator cap tester (commercial service tool) (A) and radiator cap tester adapter (commercial service tool) (B).

    Testing pressure : Refer to RADIATOR : Service Data.
  • If anything is found, repair or replace damaged parts.

Draining

Connect drain hose.

A : φ 5.5 – 6.0 mm (0.217 - 0.236 in)
B : 600 mm (23.62 in) or more

Open radiator drain cock at the bottom of radiator, and then remove radiator cap and reservoir tank cap.

: Drain hose
: vehicle front

When draining all of engine coolant in the system, open water drain plugs on cylinder block. Refer to Setting.

Remove reservoir tank if necessary, and drain engine coolant and clean reservoir tank before installing.

Check drained engine coolant for contaminants such as rust, corrosion or discoloration.

If contaminated, flush the engine cooling system. Refer to ENGINE COOLANT : Flushing.

Disconnect drain hose.

Refilling

REFILLING (FOR COOLANT REFILL TOOL)

Close drain plug.

Set the coolant refill tool [SST:KV991J0070(NI-45695-A)] (A) to the reservoir tank.

Set vacuum water injection machine [commercial tool: capable negative pressure is 90 kPa (675 mmHg, 27 inHg) or more] to the reservoir tank.

Perform water injection according to each instruction manual.

Confirm that the value of the vacuum gauge is about 96 kPa (720 mmHg, 28 inHg) and start the refilling of engine coolant

Refill engine coolant up to radiator to specified level.

Refill engine coolant up to "MAX" line level of reservoir tank and tighten the cap.

: MAX
: MIN

Start the engine and warm it up.

Stop the engine and cool down.

If necessary, refill radiator up to filler neck with engine coolant.

Refill reservoir tank to “MAX” level line with engine coolant.

: MAX
: MIN

REFILLING(EXCEPT FOR COOLANT REFILL TOOL)

Close drain plug.

Remove cap of the front heater outlet pipe assembly .

Remove drain plug of the connector .

Pour engine coolant from the part of the radiator pipe assembly.

When the engine coolant comes out from the part of the connector , stop water injection.

Pour coolant slowly in to the reservoir tank at of less than 3 ℓ (3-1/8 US qt, 2-5/8 lmp qt) a minute to allow air in system to escape.

Engine coolant capacity Refer to ENGINE COOLANT : Service Data.
(With reservoir tank at “MAX” level)

Install reservoir tank cap.

Pour coolant slowly in to the radiator pipe assembly at of less than 3 ℓ (3-1/8 US qt, 2-5/8 lmp qt) a minute to allow air in system to escape.

Install radiator cap.

Install cap of the front heater outlet pipe assembly .

Warm up engine until opening thermostat. Standard for warming-up time is approximately 10 minutes at 3,000 rpm.

  • Check thermostat opening condition by touching radiator hose (lower) to see a flow of warm water.

Stop the engine and cool down to less than approximately 50 °C.

  • Cool down using fan to reduce the time.

  • Check the engine coolant level. If the level is low, refill with reservoir tank to “MAX” level line with engine coolant and repeat the steps from Step 11.

    : MAX
    : MIN

Check flow noise, according to the following steps.

Allow the engine to become cold [approximately 50 °C or less]. Start the engine, maintain 1000 rpm for approximately 30 seconds, and increase the engine speed from 1000 to 3000 rpm. Repeat this cycle three times. Check that flow noise can be heard from the heater core during the Step b operation. If flow noise can be heard, repeat from Step 11 of Refilling to Step c of Flow Noise Verification Method. Check that the reservoir tank cap is tightened.

ENGINE COOLANT : Flushing

Install reservoir tank if removed, and radiator drain plug.

Tightening torque Refer to RADIATOR : Exploded View.

If water drain plug on cylinder block is removed, close and tighten it. Refer to Setting.

Fill radiator and reservoir tank with water and reinstall radiator cap and reservoir tank cap. Refer to ENGINE COOLANT : Refilling.

Run the engine and warm it up to normal operating temperature.

Rev the engine two or three times under no-load.

Stop the engine and wait until it cools down.

Drain water from the system. Refer to ENGINE COOLANT : Draining.

Repeat steps 1 through 6 until clear water begins to drain from radiator.

Check that the radiator cap and reservoir tank cap is tightened.