Clutch

Clutch fluid

In this manual: Clutch
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~8min read

RS5F92R : Inspection

FLUID LEAKAGE

• Check clutch line for cracks, deterioration or other damage. Replace any damaged parts.

• Check for fluid leakage by fully depressing clutch pedal while engine is running.

CAUTION:
If leakage occurs around joints, reinstall the joints or, if necessary, replace damaged parts.

FLUID LEVEL

• Check that the fluid level in the reservoir tank is within the specified range (MAX – MIN lines). • Visually check for any clutch fluid leakage around the reservoir tank.

• Check the clutch system for any leakage if the fluid level is extremely low (lower than MIN).

RS5F92R : Draining

RS5F92R : Draining

CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately and wash the affected area with water.

1. Connect a transparent vinyl hose to air bleeder of bleeding connector (1).

2. Press the lock pin (1) into the bleeding connector (2), and maintain

2. Press the lock pin (1) into the bleeding connector (2), and maintain the position.

3. Slide clutch tube (1) in the direction of the arrow as shown in the

3. Slide clutch tube (1) in the direction of the arrow as shown in the figure.

2 : Bleeding connector

Dimension “A” : 5 mm (0.20 in)

4. Depress clutch pedal to gradually discharge clutch fluid.

CAUTION:
Since the inside of clutch tube is under hydraulic pressure, hold the tube to prevent it from getting disconnected.
RS5F92R : Refilling

RS5F92R : Refilling

CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately and wash the affected area with water.

1. Check that there is no foreign material in reservoir tank, and then fill with new clutch fluid.

CAUTION:
Never reuse drained clutch fluid

.

2. Connect a transparent vinyl hose to air bleeder of bleeding connector (1).

3. Press the lock pin (1) into the bleeding connector (2), and maintain

3. Press the lock pin (1) into the bleeding connector (2), and maintain the position.

4. Slide clutch tube (1) in the direction of the arrow as shown in the

4. Slide clutch tube (1) in the direction of the arrow as shown in the figure.

2 : Bleeding connector

Dimension “A” : 5 mm (0.20 in)

5. Slowly depress clutch pedal to the full stroke position, and then release the pedal.

CAUTION:
Since the inside of clutch tube is under hydraulic pressure, hold the tube to prevent it from getting disconnected.

6. Repeat step 5 at intervals of 2 or 3 seconds until new clutch fluid is discharged.

CAUTION:
Monitor clutch fluid level in reservoir tank so as not to empty the tank.
7. Return clutch tube and lock pin in their original positions while clutch

7. Return clutch tube and lock pin in their original positions while clutch pedal is depressed.

8. Perform the air bleeding. Refer to CL-12, "RS5F92R : Air Bleeding".

RS5F92R : Air Bleeding

CAUTION:
• Monitor clutch fluid level in reservoir tank so as not to empty the tank.

• Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately and wash the affected area with water.

NOTE:

Do not use a vacuum assist or any other type of power bleeder on this system. Use of a vacuum assist or power bleeder will not purge all the air from the system.

1. Fill reservoir tank with new clutch fluid.

CAUTION:
Never reuse drained clutch fluid.
2. Connect a transparent vinyl hose to air bleeder of bleeding connector (1).

3. “Depress” and “release” the clutch pedal slowly and fully 15 times at an interval of 2 to 3 seconds and release the clutch pedal.

4. Press the lock pin (1) into the bleeding connector (2), and maintain

4. Press the lock pin (1) into the bleeding connector (2), and maintain the position.

CAUTION:
Since the inside of clutch tube is under hydraulic pressure, hold the tube to prevent it from getting disconnected.
5. Slide clutch tube (1) in the direction of the arrow as shown in the

5. Slide clutch tube (1) in the direction of the arrow as shown in the figure.

2 : Bleeding connector

Dimension “A” : 5 mm (0.20 in)

6. Depress the clutch pedal soon and hold it, and then bleed the air

6. Depress the clutch pedal soon and hold it, and then bleed the air from the piping.

CAUTION:
Since the inside of clutch tube is under hydraulic pressure, hold the tube to prevent it from getting disconnected.
7. Return clutch tube and lock pin in their original positions. 8. Release clutch pedal and wait for 5 seconds. 9. Repeat steps 3 to 8 until no bubbles are observed in the clutch fluid.

10. Check that the fluid level in the reservoir tank is within the specified range after air bleeding. Refer to CL- 10, "RS5F92R : Inspection".

RS6F94R : Inspection

FLUID LEAKAGE

• Check clutch line for cracks, deterioration or other damage. Replace any damaged parts.

• Check for fluid leakage by fully depressing clutch pedal while engine is running.

CAUTION:
If leakage occurs around joints, reinstall the joints or, if necessary, replace damaged parts

.

FLUID LEVEL

• Check that the fluid level in the reservoir tank is within the specified range (MAX – MIN lines). • Visually check for any clutch fluid leakage around the reservoir tank.

• Check the clutch system for any leakage if the fluid level is extremely low (lower than MIN).

RS6F94R : Draining

RS6F94R : Draining

CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately and wash the affected area with water.

1. Connect a transparent vinyl hose to air bleeder of bleeding connector (1).

2. Press the lock pin (1) into the bleeding connector (2), and maintain

2. Press the lock pin (1) into the bleeding connector (2), and maintain the position.

3. Slide bleeding connector (1) in the direction of the arrow as

3. Slide bleeding connector (1) in the direction of the arrow as shown in the figure.

2 : Clutch housing

Dimension “A” : 10 mm (0.39 in)

4. Depress clutch pedal to gradually discharge clutch fluid.

4. Depress clutch pedal to gradually discharge clutch fluid.

CAUTION:
Since the inside of clutch tube is under hydraulic pressure, hold the tube to prevent it from getting disconnected.

RS6F94R : Refilling

CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately and wash the affected area with water.

1. Check that there is no foreign material in reservoir tank, and then fill with new clutch fluid.

CAUTION:
Never reuse drained clutch fluid.

2. Connect a transparent vinyl hose to air bleeder of bleeding connector (1).

3. Press the lock pin (1) into the bleeding connector (2), and maintain

3. Press the lock pin (1) into the bleeding connector (2), and maintain the position.

4. Slide bleeding connector (1) in the direction of the arrow as

4. Slide bleeding connector (1) in the direction of the arrow as shown in the figure.

2 : Clutch housing

Dimension “A” : 10 mm (0.39 in)

5. Slowly depress clutch pedal to the full stroke position, and then

5. Slowly depress clutch pedal to the full stroke position, and then release the pedal.

CAUTION:
Since the inside of clutch tube is under hydraulic pressure, hold the tube to prevent it from getting disconnected.

6. Repeat step 5 at intervals of 2 or 3 seconds until new clutch fluid is discharged.

CAUTION:
Monitor clutch fluid level in reservoir tank so as not to empty the tank.
7. Return clutch tube and lock pin in their original positions while clutch pedal is depressed.

8. Perform the air bleeding. Refer to CL-15, "RS6F94R : Air Bleeding".

RS6F94R : Air Bleeding

CAUTION:
• Monitor clutch fluid level in reservoir tank so as not to empty the tank.

• Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately and wash the affected area with water.

NOTE:

Do not use a vacuum assist or any other type of power bleeder on this system. Use of a vacuum assist or power bleeder will not purge all the air from the system.

1. Fill reservoir tank with new clutch fluid.

CAUTION:
Never reuse drained clutch fluid.
2. Connect a transparent vinyl hose to air bleeder of bleeding connector (1).

3. “Depress” and “release” the clutch pedal slowly and fully 15 times at an interval of 2 to 3 seconds and release the clutch pedal.

4. Press the lock pin (1) into the bleeding connector (2), and maintain

4. Press the lock pin (1) into the bleeding connector (2), and maintain the position.

CAUTION:
Since the inside of clutch tube is under hydraulic pressure, hold the tube to prevent it from getting disconnected.
5. Slide bleeding connector (1) in the direction of the arrow as

5. Slide bleeding connector (1) in the direction of the arrow as shown in the figure.

2 : Clutch housing

Dimension “A” : 10 mm (0.39 in)

6. Depress the clutch pedal soon and hold it, and then bleed the air

6. Depress the clutch pedal soon and hold it, and then bleed the air from the piping.

CAUTION:
Since the inside of clutch tube is under hydraulic pressure, hold the tube to prevent it from getting disconnected.
7. Return clutch tube and lock pin in their original positions. 8. Release clutch pedal and wait for 5 seconds. 9. Repeat steps 3 to 8 until no bubbles are observed in the clutch fluid.

10. Check that the fluid level in the reservoir tank is within the specified range after air bleeding. Refer to CL- 13, "RS6F94R : Inspection".