Transaxle & transmissioN CVT: RE0F11A

CVT fluid

In this manual: Transaxle & transmissioN CVT: RE0F11A
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~5min read

Replacement

CVT fluid : Refer to TM-512, "General Specification".

Fluid capacity : Refer to TM-512, "General Specificatio

CAUTION:
• Use only Genuine NISSAN CVT Fluid NS-2. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-2 will damage the CVT, which is not covered by the (NISSAN new vehicle limited) warranty.

• Always use shop paper. Never use shop cloth.

• Replace a drain plug gasket with new ones at the final stage of the operation when installing. • Use caution when looking into the drain hole as there is a risk of dripping fluid entering the eye.

• After replacement, always perform CVT fluid leakage check.

1. Select “Data Monitor” in “TRANSMISSION” using CONSULT-III. 2. Select “FLUID TEMP” and confirm that the CVT fluid temperature is 40 °C or less. 3. Check that the selector lever is in the “P” position, then completely engage the parking brake. 4. Lift up the vehicle. 5. Remove the drain plug and overflow tube and drain the CVT fluid from the oil pan. TM-493, "Exploded View".

6. Install the charging pipe set (KV311039S0) (A) into the drain hole.

CAUTION:
Tighten the charging pipe by hand.

7. Install the ATF changer hose (B) to the charging pipe.

CAUTION:
Press the ATF changer hose all the way onto the charging pipe until it stops.
8. Fill approximately 3 liter (2-5/8 lmp qt) of the CVT fluid.

8. Fill approximately 3 liter (2-5/8 lmp qt) of the CVT fluid.

9. Remove the ATF changer hose and charging pipe, then install the drain plug.

NOTE

:
Perform this work quickly because CVT fluid leaks.

10. Lift down the vehicle. 11. Start the engine.

12. While depressing the brake pedal, shift the selector lever to the entire position from “P” to “L”, and shift it to the “P” position.

NOTE

:
Hold the lever at each position for 5 seconds.

13. Check that the CONSULT-III “Data monitor” in “FLUID TEMP” is 35 °C to 45 °C. 14. Stop the engine. 15. Lift up the vehicle. 16. Remove the drain plug, and then drain CVT fluid from oil pan. 17. Repeat steps 6 to 16 (one time).

18. Install the overflow tube. Refer to TM-493, "Exploded View".

CAUTION:
Be sure to tighten to the specified torque. If it is not tightened to the specified torque, the tube may be damaged.
19. Install the charging pipe set (KV311039S0) (A) into the drain

19. Install the charging pipe set (KV311039S0) (A) into the drain hole.

CAUTION:
Tighten the charging pipe by hand.

20. Install the ATF changer hose (B) to the charging pipe.

CAUTION:
Press the ATF changer hose all the way onto the charging pipe until it stops.
21. Fill approximately 3 liter (2-5/8 lmp qt) of the CVT fluid.

22. Remove the ATF changer hose and charging pipe, then install the drain plug.

NOTE

:
Perform this work quickly because CVT fluid leaks.

23. Lift down the vehicle. 24. Start the engine.

25. While depressing the brake pedal, shift the selector lever to the entire position from “P” to “L”, and shift it to the “P” position.

NOTE

:
Hold the lever at each position for 5 seconds.

26. Check that the CONSULT-III “Data monitor” in “FLUID TEMP” is 35 °C to 45 °C. 27. Lift up the vehicle.

28. Remove the drain plug and confirm that the CVT fluid is drained from the overflow tube.

CAUTION:
Perform this work with the vehicle idling.
NOTE:

If the CVT fluid is not drained, refer to “Adjustment” and refill with the CVT fluid.

29. When the flow of CVT fluid slows to a drip, tighten the drain plug to the specified torque. TM-493, "Exploded View".

CAUTION:
Never reuse drain plug gasket.
30. Lift down the vehicle. 31. Select “Data Monitor” in “TRANSMISSION” using CONSULT-III. 32. Select “CONFORM CVTF DETERIORTN”. 33. Select “Erase”.

34. Stop the engine.

Adjustment

CVT fluid : Refer to TM-512, "General Specification".

Fluid capacity : Refer to TM-512, "General Specification".

CAUTION:
• Use only Genuine NISSAN CVT Fluid NS-2. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-2 will damage the CVT, which is not covered by the (NISSAN new vehicle limited) warranty. • During adjustment of the CVT fluid level, check CONSULT-III so that the oil temperature may be maintained from 35 to 45 °C.

• Use caution when looking into the drain hole as there is a risk of dripping fluid entering the eye.

1. Check that the selector lever is in the “P” position, then completely engage the parking brake. 2. Start the engine.

3. Adjust the CVT fluid temperature to be approximately 40 °C.

NOTE

:
The CVT fluid is largely affected by temperature. Therefore be sure to use CONSULT-III and check the “FLUID TEMP” under “TRANSMISSION” in “Data Monitor” while adjusting.

4. While depressing the brake pedal, shift the selector lever to the entire position from “P” to “L”, and shift it to the “P” position.

NOTE

:
Hold the lever at each position for 5 seconds.

5. Lift up the vehicle. 6. Check that there is no CVT fluid leakage. 7. Remove the drain plug. Refer to TM-493, "Exploded View".

8. Install the charging pipe set (KV311039S0) (A) into the drain plug hole.

CAUTION:
Tighten the charging pipe by hand.

9. Install the ATF changer hose (B) to the charging pipe.

CAUTION:
Press the ATF changer hose all the way onto the charging pipe until it stops.

10. Fill approximately 0.5 liter (1/2 lmp qt) of the CVT fluid.

11. Remove the ATF changer hose from the charging pipe, and

11. Remove the ATF changer hose from the charging pipe, and check that the CVT fluid drains out from the charging pipe. If it does not drain out, perform charging again.

CAUTION:
Perform this work with the vehicle idling.
12. When the flow of CVT fluid slows to a drip, remove the charging pipe from the oil pan.

13. Tighten the drain plug to the specified torque. Refer to TM-493, "Exploded View".

CAUTION:
Never reuse drain plug gasket.
14. Lift down the vehicle.

15. Stop the engine.