Driveline rear final drive: RTVS

Drive pinion

In this manual: Driveline rear final drive: RTVS
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~9min read
010203040501.31N·mlb·ft
Tightening torque found on this page

Exploded View

1. Filler plug

1. Filler plug
2. Gasket
3. Drain plug
4. Breather tube
5. Clip
6. Breather hose
7. Breather
8. sub-harness clip
9. sub-harness
10. Rear cover
11. Center stem
12. Side bearing (right) 13. Side bearing adjusting shim (right) 14. Side oil seal (right) 15. Connector clip
16. Electric controlled coupling (right) 17. Electric controlled coupling oil seal 18. Reamer bolt
19. Drive pinion
20. Drive pinion adjusting shim 21. Pinion rear bearing
22. Collapsible spacer
23. Breather
24. Gear carrier
25. Carrier bracket (right) 26. Pinion front bearing 27. Front oil seal
28. Companion flange
29. Drive pinion lock nut 30. Carrier bracket (left) 31. Drive gear
32. Side bearing (left) 33. Side bearing adjusting shim (left) 34. Electric controlled coupling (left) 35. Side oil seal (left)

A. Oil seal lip B. Gear carrier mounting face

disassembly.: Always replace after every
disassembly. : N·m (kg-m, ft-lb): Select with proper thickness.
: Apply gear oil.: N·m (kg-m, ft-lb)
: Apply anti-corrosive oil.: Apply gear oil.
: Apply multi purpose grease: Apply anti-corrosive oil.


: Apply Genuine Liquid Gasket 1217: Apply multi purpose grease
or equivalent.: Apply Genuine Liquid Gasket 1217
or equivalent.

Disassembly

1. Remove electric controlled coupling. Refer to DLN-147, "Disassembly". 2. Remove center stem assembly. Refer to DLN-152, "Disassembly".

3. Remove drive pinion lock nut with the flange wrench (A) (commercial service tool).

4. Put matching mark (B) on the end of drive pinion. The matching

4. Put matching mark (B) on the end of drive pinion. The matching mark should be in line with the matching mark (A) on companion flange (1).

CAUTION:
For matching mark, use paint. Never damage companion flange and drive pinion.
NOTE:

The matching mark on the final drive companion flange indicates the maximum vertical runout position.

When replacing companion flange, matching mark is not necessary.

5. Remove companion flange using the pullers (A) (commercial

5. Remove companion flange using the pullers (A) (commercial service tool).

6. Press drive pinion assembly out of gear carrier.

6. Press drive pinion assembly out of gear carrier.

CAUTION:
Never drop drive pinion assembly.
7. Remove front oil seal. 8. Remove pinion front bearing inner race.

9. Remove collapsible spacer.

10. Remove pinion rear bearing inner race and pinion height adjusting

10. Remove pinion rear bearing inner race and pinion height adjusting washer with the replacer (A) (commercial service tool).

11. Remove pinion height adjusting washer.

12. Tap pinion front/rear bearing outer races uniformly using a brass

12. Tap pinion front/rear bearing outer races uniformly using a brass rod or equivalent to remove them.

CAUTION:
Never damage gear carrier.

13. Perform inspection after disassembly. Refer to DLN-165, "Inspection".

Assembly

Assembly

1. Install pinion front bearing outer race to the gear carrier with drift (A) (SST: ST17130000).

CAUTION:
• At first, using a hammer, tap bearing outer race until it becomes flat to gear carrier.

• Never reuse pinion front and rear bearing outer race.

2. Install pinion rear bearing outer race to the gear carrier with drift

2. Install pinion rear bearing outer race to the gear carrier with drift (A) (SST: KV38100300).

CAUTION:
• At first, using a hammer, tap bearing outer race until it becomes flat to gear carrier.

• Never reuse pinion front and rear bearing outer race.

3. Temporarily install pinion height adjusting washer (1).

3. Temporarily install pinion height adjusting washer (1).

When hypoid gear set has been replaced • Select pinion height adjusting washer. Refer to DLN-164, "Adjustment".

When hypoid gear set has been reused • Temporarily install the removed pinion height adjusting washer or same thickness washer to drive pinion.

CAUTION:
Pay attention to the direction of pinion height adjusting washer. (Assemble as shown in the figure.)
4. Install pinion rear bearing inner race (1) to drive pinion with the

4. Install pinion rear bearing inner race (1) to drive pinion with the drift (A) (SST: ST30032000).

CAUTION:
Never reuse pinion rear bearing inner race.

5. Check and adjust the tooth contact and back lash of drive gear and drive pinion following the procedure below.

a. Assemble drive pinion into gear carrier.

CAUTION:
• Never assemble a collapsible spacer.

• Apply gear oil to pinion rear bearing.

b. Assemble pinion front bearing inner race to drive pinion assembly.

CAUTION:
• Never reuse pinion front bearing inner race.

• Apply gear oil to pinion front bearing.

c. Using drift (A) (SST: ST37710000), press the pinion front bearing

c. Using drift (A) (SST: ST37710000), press the pinion front bearing inner race to drive pinion as far as drive pinion nut can be tightened.

d. Install companion flange (1).

d. Install companion flange (1).

CAUTION:
Never assemble front oil seal.
NOTE:

When reusing drive pinion, align the matching mark (B) of drive pinion with the matching mark (A) of companion flange, and then install companion flange.

e. Temporarily tighten removed drive pinion nut to drive pinion

e. Temporarily tighten removed drive pinion nut to drive pinion using flange wrench (commercial service tool).

NOTE

:
Use removed drive pinion nut only for the preload measurement.

f. Rotate drive pinion more than 20 times to adjust bearing.

g. Tighten to drive pinion lock nut using flange wrench (commercial service tool), while adjusting pinion bearing preload torque using preload gauge (A) (SST: ST3127S000).

Pinion bearing preload (without oil seal) : 1.0 - 1,3 N·m

CAUTION:
Drive pinion lock nut is tightened with no collapsible spacer. Be careful not to overtighten it. While measuring the preload, tighten it by 5° to 10°.

h. Assemble removed drive side bearing adjusting washer or same thickness of it and install center stem assembly. Refer to DLN- 153, "Assembly".

CAUTION:
Apply differential gear oil to the side bearings.
i. Check and adjust tooth contact, drive gear to drive pinion backlash. Refer

i. Check and adjust tooth contact, drive gear to drive pinion backlash. Refer to DLN-154, "Adjustment". j. Remove center stem assembly. k. Remove companion flange. l. Remove drive pinion assembly from gear carrier. m. Remove pinion front bearing inner race.

6. Assemble collapsible spacer.

CAUTION:
Never reuse collapsible spacer.

7. Assemble drive pinion into gear carrier.

CAUTION:
Apply gear oil to pinion rear bearing.

8. Assemble pinion front bearing inner race to drive pinion assembly.

CAUTION:
• Never reuse pinion front bearing inner race.

• Apply gear oil to pinion front bearing.

9. Using drift (A) (SST: ST37710000), press the pinion front bearing inner race to drive pinion as far as drive pinion nut can be tightened.

10. Install front oil seal as shown in figure with the drift (A) (commercial

10. Install front oil seal as shown in figure with the drift (A) (commercial service tool).

CAUTION:
• Never reuse oil seal. • When installing, never incline oil seal.

• Apply multi-purpose grease onto oil seal lips, and gear oil onto the circumference of oil seal.

11. Install companion flange (1).

11. Install companion flange (1).

NOTE

:
When reusing drive pinion, align the matching mark (B) of drive pinion with the matching mark (A) of companion flange, and then install companion flange.

12. Apply anti-corrosion oil to the thread and seat of drive pinion

12. Apply anti-corrosion oil to the thread and seat of drive pinion lock nut, and temporarily tighten drive pinion lock nut to drive pinion, using flange wrench (commercial service tool).

CAUTION:
Never reuse drive pinion lock nut.

13. Adjust to the drive pinion lock nut tightening torque and pinion bearing preload torque, using preload gauge (A) (SST: ST3127S000)

Pinion bearing preload : Refer to DLN-167, "Preload Torque".

CAUTION:
• Adjust to the lower limit of the drive pinion lock nut tightening torque first. • If the preload torque exceeds the specified value, replace collapsible spacer and tighten it again to adjust. Never loosen drive pinion lock nut to adjust the preload torque.

• After adjustment, rotate drive pinion back and forth 2 to 3 times to check for unusual noise, rotation malfunction, and other malfunctions.

14. Install center stem assembly. Refer to DLN-153, "Assembly".

CAUTION:
Never install rear cover at this timing.
15. Check and adjust drive gear runout, tooth contact, drive gear to drive pinion backlash, and companion flange runout. Refer to DLN-154, "Adjustment" and DLN-164, "Adjustment". 16. Check total preload torque. Refer to DLN-154, "Adjustment".

17. Install rear cover. Refer to DLN-153, "Assembly".

Adjustment

Adjustment

PINION GEAR HEIGHT

If the hypoid gear set has been replaced, select the pinion height adjusting washer.

1. Use the formula below to calculate pinion height adjusting washer thickness.

Washer selection equation: T = T0 + (t1− t2)
T: Correct washer thickness T0: Removed washer thickness t1: Old drive pinion head letter “H × 0.01” (“H”: machined tolerance 1/100 mm × 100) t2: New drive pinion head letter “H × 0.01” (“H”: machined tolerance 1/100 mm × 100)

Example:

Example:
T = 3.21 + [(2 × 0.01) − (−1 × 0.01)] = 3.24 T0: 3.21
t1: +2
t2: −1

2. Select the proper pinion height adjusting washer. For selecting adjusting washer, refer to the latest parts information.

CAUTION:
If unable to find a washer of desired thickness, use a washer with thickness closest to the calculated value.

Example:
Calculated value... T = 3.22 mm Used washer... T = 3.21 mm

COMPANION FLANGE RUNOUT

1. Fit a dial indicator onto the companion flange face (inner side of the rear propeller shaft mounting bolt holes).

2. Rotate companion flange to check for runout.

Companion flange runout : Refer to DLN-167, "Companion Flange Runout".

3. Fit a test indicator to the inner side of companion flange (socket diameter).

4. Rotate companion flange to check for runout.

Companion flange runout : Refer to DLN-167, "Companion

Companion flange runout : Refer to DLN-167, "Companion Flange Runout".

5. If the runout value is outside the runout limit, follow the procedure below to adjust.

a. Check for runout while changing the phase between companion flange and drive pinion by 90° step, and search for the position where the runout is the minimum. b. If the runout value is still outside of the limit after the phase has been changed, replace companion flange.

c. If the runout value is still outside of the limit after companion flange has been replaced, possible cause will be an assembly malfunction of drive pinion and electric controlled coupling, malfunctioning coupling bearing, or malfunctioning of electric controlled coupling.

Inspection

INSPECTION AFTER DISASSEMBLY

Drive Gear and Drive Pinion • Clean up the disassembled parts. • If the gear teeth never mesh or line-up correctly, determine the cause and adjust or replace as necessary.

• If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new drive gear and drive pinion as a set.

Bearing
• Clean up the disassembled parts.

• If any chipped (by friction), pitted, worn, rusted or scratched marks, or unusual noise from the bearing is observed, replace as a bearing assembly (as a new set).

Oil Seal
• Whenever disassembled, replace.

• If wear, deterioration of adherence (sealing force lips), or damage is detected on the lips, replace them.

Companion Flange
• Clean up the disassembled parts.

• If any chipped mark [about 0.1 mm, (0.004 in)] or other damage on the contact sides of the lips of the companion flange is found, replace.