Engine Mechanical HR16DE

Fuel injector and fuel tube

In this manual: Engine Mechanical HR16DE
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~7min read

Exploded View

1. Stud bolt

1. Stud bolt
2. O-ring (green)
3. Fuel injector (front) 4. Clip
5. Fuel injector (rear) 6. O-ring (black)
7. Fuel tube protector
8. Fuel tube
9. Fuel feed hose
10. Quick connector cap

A. To centralized under-floor piping

disassembly.: Always replace after every
disassembly.

: N·m (kg-m, ft-lb): N·m (kg-m, in-lb)
: Should be lubricated with oil.: N·m (kg-m, ft-lb)
CAUTION:: Should be lubricated with oil.


CAUTION:
Never remove or disassemble parts unless instructed as shown in the figure.

Removal and Installation

WARNING:
• Put a “CAUTION: FLAMMABLE” sign in the workshop. • Be sure to work in a well ventilated area and furnish workshop with a CO2 fire extinguisher.

• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.

REMOVAL

1. Release the fuel pressure. Refer to EC-551, "Work Procedure". 2. Remove intake manifold. Refer to EM-163, "Exploded View".

3. Disconnect quick connector with the following procedure. Disconnect fuel feed hose from fuel tube.

1 : Quick connector cap

NOTE

:
There is no fuel return path.

a. Remove quick connector cap (engine side) (1) from quick connector

a. Remove quick connector cap (engine side) (1) from quick connector connection.

b. Disconnect fuel feed hose from hose clamp.

c. With the sleeve side of quick connector release facing quick connector,

c. With the sleeve side of quick connector release facing quick connector, install quick connector release (commercial service tool) onto fuel tube.

d. Insert quick connector release (A) into quick connector (2) until sleeve (B) contacts and goes no further. Hold quick connector release on that position.

D : Insert and retain

CAUTION:
Inserting quick connector release hard will not disconnect quick connector. Hold quick connector release where it contacts and goes no further.
e. Draw and pull out quick connector straight from fuel tube (1).

e. Draw and pull out quick connector straight from fuel tube (1).

CAUTION:
• Pull quick connector (E) holding position (C) in the figure. • Never pull with lateral force applied. O-ring inside quick connector may be damaged. • Prepare container and cloth beforehand as fuel will leakage out. • Avoid fire and sparks. • Keep parts away from heat source. Especially, be careful when welding is performed around them. • Never expose parts to battery electrolyte or other acids. • Never bend or twist connection between quick connector and fuel feed tube during installation/ removal.

• To keep clean the connecting portion and to avoid damage and foreign materials, cover them completely with plastic bags, etc. (A) or something similar.

4. Disconnect harness connector from fuel injector.

4. Disconnect harness connector from fuel injector.

5. Remove fuel tube protector.

• Loosen mounting bolts in reverse order as shown in the figure.

: Engine front


6. Remove fuel tube and fuel injector assembly.

6. Remove fuel tube and fuel injector assembly.

• Loosen mounting bolts in reverse order as shown in the figure.

CAUTION:: Engine front


CAUTION:
• When removing, be careful to avoid any interference with fuel injector.

• Use a shop cloth to absorb any fuel leakage from fuel tube.

7. Remove fuel injector from fuel tube with the following procedure:

7. Remove fuel injector from fuel tube with the following procedure: a. Open and remove clip (1).

b. Remove fuel injector (3) and (4) from fuel tube (2) by pulling straight.

CAUTION:
• Be careful with remaining fuel that may go out from fuel tube. • Be careful not to damage fuel injector nozzle during removal. • Never bump or drop fuel injector.

• Never disassemble fuel injector.

INSTALLATION

INSTALLATION

1. Note the following, and install O-rings to fuel injector.

CAUTION:
• Upper and lower O-rings are different. Be careful not to confuse them.

Fuel tube side : Black Nozzle side : Gre

• Handle O-ring with bare hands. Never wear gloves. • Lubricate O-ring with new engine oil. • Never clean O-ring with solvent. • Check that O-ring and its mating part are free of foreign material. • When installing O-ring, be careful not to scratch it with tool or fingernails. Also be careful not to twist or stretch O-ring. If O-ring is stretched while installing, never insert it quickly into fuel tube.

• Insert O-ring straight into fuel tube. Never decenter or twist it.

2. Install fuel injector to fuel tube with the following procedure:

a. Insert clip (2) into clip mounting groove on fuel injector (4).

3 : O-ring (black)3 : O-ring (black) 5 : O-ring (green) 5 : O-ring (green)

• Insert clip so that protrusion (F) of fuel injector matches cut-out (D) of clip.

CAUTION:
• Never reuse clip. Replace it with a new one.

• Be careful to keep clip from interfering with O-ring. If interference occurs, replace O-ring.

b. Insert fuel injector into fuel tube (1) with clip attached.

• Insert it while matching it to the axial center. • Insert fuel injector so that protrusion (B) of fuel tube matches cut-out (C) of clip.

• Check that fuel tube flange (A) is securely fixed in flange fixing groove (E) on clip.

c. Check that installation is complete by checking that fuel injector does not rotate or come off.

3. Set fuel tube and fuel injector assembly at its position for installation

3. Set fuel tube and fuel injector assembly at its position for installation on cylinder head.

CAUTION:
For installation, be careful not to interfere with fuel injector nozzle.

4. Install fuel tube and injector assembly onto cylinder.

• Tighten mounting bolts in numerical order as shown in the figure.

: Engine front


5. Install fuel tube protector.

5. Install fuel tube protector.

• Tighten mounting bolts in numerical order as shown in the figure.

: Engine front


6. Connect harness connector to fuel injector.

6. Connect harness connector to fuel injector.

7. Connect fuel feed tube with the following procedure.

a. Check for damage or foreign material on the fuel tube and quick connector. b. Apply new engine oil lightly to area around the top of fuel tube.

c. Align center to insert quick connector straightly into fuel tube.

• Insert quick connector (1) to fuel tube until the top spool (C) on fuel tube is inserted completely and the 2nd level spool (D) is positioned slightly below quick connector bottom end.

B : Upright insertion E : Fitted condition

CAUTION:
• Hold (A) position in the figure when inserting fuel tube into quick connector. • Carefully align center to avoid inclined insertion to prevent damage to O-ring inside quick connector. • Insert until you hear a “click” sound and actually feel the engagement.

• To avoid misidentification of engagement with a similar sound, be sure to perform the next step.

d. Pull quick connector hard by hand holding position. Check it is completely

d. Pull quick connector hard by hand holding position. Check it is completely engaged (connected) so that it does not come out from fuel tube.

e. Install quick connector cap (engine side) (1) to quick connector connection.

• Install quick connector cap (engine side) with the side arrow facing quick connector side (fuel feed tube side).

CAUTION:
• Check that the quick connector and fuel tube are securely engaged with the quick connector cap (engine side) mounting groove.

• Quick connector may not be connected correctly if quick connector cap (engine side) cannot be installed easily. Remove the quick connector cap (engine side), and then check the connection of quick connector again.

f. Install fuel feed hose to hose clamp.

f. Install fuel feed hose to hose clamp.

8. Install remaining parts in the reverse order of removal.

Inspection

INSPECTION AFTER INSTALLATION

Check on Fuel Leakage 1. Turn ignition switch “ON” (with the engine stopped). With fuel pressure applied to fuel piping, check there are no fuel leakage at connection points.

NOTE

:
Use mirrors for checking at points out of clear sight.

2. Start the engine. With engine speed increased, check again that there are no fuel leakage at connection points.

CAUTION:
Never touch the engine immediately after stopped, as the engine becomes extremely hot.