Fuel System MR16DDT

Fuel tank

In this manual: Fuel System MR16DDT
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~10min read

2WD : Exploded View

1. Fuel filler cap

1. Fuel filler cap
2. Grommet
3. Fuel filler tube
4. EVAP canister hose
5. Fuel tank mounting band (RH) 6. Fuel tank mounting band (LH) 7. Fuel tank
8. Clamp
9. Fuel filler hose
10. Vent hose

: N?·m (kg-m, ft-lb)Vehicle front
2WD : Removal and Installation: N?·m (kg-m, ft-lb)


2WD : Removal and Installation

WARNING:
Be sure to read ???General Precautions??? when working on the fuel system. Refer to FL-3, "General Precautions".

REMOVAL

1. Drain fuel from fuel tank if necessary. Refer to FL-6, "2WD : Removal and Installation".

CAUTION:
• Because fuel tank forwardly inclines and becomes unstable when installing/removing, fuel should be drained if found the remaining quantity.

• Situate vehicle on a flat and solid surface.

2. Remove RH rear wheel. 3. Perform steps 2 to 7 of ???REMOVAL??? in ???FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY??? on fuel level sensor unit, fuel filter and fuel pump assembly. Refer to FL-6, "2WD : Removal and Installation". 4. Remove center muffler. Refer to DLN-121, "Exploded View". 5. Remove insulator on vehicle side located above center and main mufflers. 6. Move parking brake cable from the lower face of fuel tank. Then remove clips for parking brake cable. 7. Remove brake tube protector.

8. Disconnect fuel filler hose at fuel tank side.

1 : Filler tube
2 : Vent hose
3 : Filler hose

9. Remove vent hose at RH rear wheel well side

9. Remove vent hose at RH rear wheel well side

10. Remove EVAP hose (1) at front side of fuel tank (2).

: Vehicle front


• Remove quick connector in the following procedures.

• Remove quick connector in the following procedures.

- Pinch quick connector square-part (A) with your fingers, and pull out the quick connector (1) by hand.

- If quick connector and tube on vehicle are stuck, push and pull several times until they move, and pull out.

CAUTION:
• The tube can be removed when the tabs are completely depressed. Never twist it more than necessary. • Never use any tools to disconnect quick connector. • Keep the resin tube away from heat. Be especially careful when welding near the tube. • Prevent acid liquid such as battery electrolyte, etc. from getting on the resin tube. • Never bend or twist resin tube during installation and disconnection. • To keep the connecting portion clean and to avoid damage and foreign materials, cover them completely with plastic bags or something similar.

• Never insert plug, preventing damage on O-ring in quick connector.


11. Remove EVAP hose (1) in the back for fuel tank side.

11. Remove EVAP hose (1) in the back for fuel tank side.

: Vehicle front


12. If necessary, remove mounting screw and quick connectors and

12. If necessary, remove mounting screw and quick connectors and slide the EVAP canister rearward to remove it from the fuel tank.

13. Disconnect EVAP hose and vent tube at the position shown in the figure.

• Instruction for quick connector of EVAP hose and vent tube, refer to the following:

Vent tube

Vent tube
• Remove quick connector in the following procedures.

- Pinch quick connector square-part (A) with your fingers, and pull out the quick connector (1) by hand.

- If quick connector and tube on vehicle are stuck, push and pull several times until they move, and pull out.

CAUTION:
• The tube can be removed when the tabs are completely depressed. Never twist it more than necessary. • Never use any tools to disconnect quick connector. • Keep the resin tube away from heat. Be especially careful when welding near the tube. • Prevent acid liquid such as battery electrolyte, etc. from getting on the resin tube. • Never bend or twist resin tube during installation and disconnection. • To keep the connecting portion clean and to avoid damage and foreign materials, cover them completely with plastic bags (A) or something similar.

• Never insert plug, preventing damage on O-ring in quick connector.


14. Support the center part of fuel tank (1) with transmission jack

14. Support the center part of fuel tank (1) with transmission jack (B).

CAUTION:
Securely support the fuel tank with a piece of wood (A).
15. Remove fuel tank mounting bands (RH and LH).

15. Remove fuel tank mounting bands (RH and LH).

16. Lower transmission jack carefully to remove fuel tank while holding it by hand.

CAUTION:
Fuel tank may be in an unstable condition because of the shape of fuel tank bottom. Never rely on jack too much. Be sure to hold tank securely.

INSTALLATION

Note the following, and install in the reverse order of removal.

Fuel Tank 1. Temporarily tighten bolts [except (2)] in numerical order as shown in the figure.

A : Under view : Vehicle front


2. Tighten bolt (2) to specified torque, pressing fuel tank in the

2. Tighten bolt (2) to specified torque, pressing fuel tank in the direction ( figure.) shown in the
figure.

3. Tighten bolts [except (2)] to specified torque in the reverse order as shown in the figure.

Fuel Filler Hose
• Surely clamp fuel hose insert fuel filler hose to the length below.

Fuel filler hose : 35 mm (1.38 in) The other hose : 25 mm (0.98 in)

• Be sure hose clamp is not placed on swelled area of fuel filler tube. • Install fuel filler hose to fuel tank, paying attention to install mark. Marking faces downward.

• Tighten fuel filler hose clamp so that the remaining length of screw thread becomes to the following.

Fuel filler tube side : 8 - 12 mm (0.28 - 0.43 in) Fuel tank side : 5 - 9 mm (0.25 - 0.35 in)

EVAP Hose and Vent Tube 1. Check connections for damage or foreign material. 2. Align the matching side connection part with the center of shaft, and insert connector straight until it clicks.

3. After connecting, pull out quick connector and centralized under floor piping by hand. Check connections are secure.

A : Pull

2WD : Inspecti

2WD : Inspecti

INSPECTION AFTER INSTALLATION

Use the following procedure to check for fuel leakage.

1. Turn ignition switch ???ON??? (with engine stopped), and check connections for leakage by applying fuel pressure to fuel piping.

2. Start engine and rev it up and check there are no fuel leakage at the fuel system tube and hose connections.

4WD : Exploded View

1. Fuel filler cap

1. Fuel filler cap
2. Grommet
3. Fuel filler tube
4. Clamp
5. Fuel filler hose
6. Fuel tank band (RH)
7. Protector
8. Fuel tank band (LH)
9. Fuel tank
10. Clamp
11. Vent hose

A. To EVAP canister

: N?·m (kg-m, ft-lb)Vehicile front
: N?·m (kg-m, in-lb): N?·m (kg-m, ft-lb)
4WD : Removal and Installation: N?·m (kg-m, in-lb)


4WD : Removal and Installation

REMOVAL

WARNING:
Be sure to read ???General Precautions??? when working on the fuel system. Refer to FL-3, "General Precautions".
CAUTION:
• Because fuel tank forwardly inclines and becomes unstable when installing/removing, fuel should be drained if found the remaining quantity.

• Situate vehicle on a flat and solid surface.

1. Drain fuel from fuel tank if necessary. 2. Perform the steps 2 to 7 of ???REMOVAL??? in ??? FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY???. Refer to FL-11, "4WD : Removal and Installation". 3. Remove center muffler. 4. Remove propeller shaft. Refer to DLN-121, "Exploded View". 5. Remove protector from fuel tank.

6. Remove fuel filler hose (3) at fuel tank side.

1 : Vent tube
2 : EVAP hose
: Vehicle front


7. Disconnect vent hose connector (1).

7. Disconnect vent hose connector (1). 8. Disconnect vent tube and EVAP hose at rear side of fuel tank.

• Instruction for quick connector (A) of EVAP tube and vent hose. Refer toFL-11, "4WD : Removal and Installation".

9. Remove parking brake cable mounting bolts. Refer to PB-4, "Exploded

9. Remove parking brake cable mounting bolts. Refer to PB-4, "Exploded View". 10. Disconnect ABS harness connector from fuel tank mounting band.

11. Support left of fuel tank (1) with transmission jack (A), and them remove fuel tank band (RH) (2).

10. Clamp
11. Vent hose

A. To EVAP canister

: N·m (kg-m, ft-lb)Vehicile front
: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
4WD : Removal and Installation: N·m (kg-m, in-lb)


4WD : Removal and Installation

REMOVAL

CAUTION:
• Because fuel tank forwardly inclines and becomes unstable when installing/removing, fuel should be drained if found the remaining quantity. • Situate vehicle on a flat and solid surface. 1. Drain fuel from fuel tank if necessary. 2. Perform the steps 2 to 7 of “REMOVAL” in “ FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY”. Refer to FL-11, "4WD : Removal and Installation". 3. Remove center muffler. 4. Remove propeller shaft. Refer to DLN-121, "Exploded View". 5. Remove protector from fuel tank.

6. Remove fuel filler hose (3) at fuel tank side.

1 : Vent tube
2 : EVAP hose
7. Disconnect vent hose connector (1).: Vehicle front


7. Disconnect vent hose connector (1).

8. Disconnect vent tube and EVAP hose at rear side of fuel tank.

• Instruction for quick connector (A) of EVAP tube and vent hose. Refer toFL-11, "4WD : Removal and Installation".

9. Remove parking brake cable mounting bolts. Refer to PB-4, "Exploded

9. Remove parking brake cable mounting bolts. Refer to PB-4, "Exploded View". 10. Disconnect ABS harness connector from fuel tank mounting band.

11. Support left of fuel tank (1) with transmission jack (A), and them remove fuel tank band (RH) (2).

12. Support right of fuel tank(1) with transmission jack (A), and them

12. Support right of fuel tank(1) with transmission jack (A), and them remove fuel tank band mounting bolts (LH).

13. Supporting with hands, descend transmission jack carefully, and remove

13. Supporting with hands, descend transmission jack carefully, and remove fuel tank.

CAUTION:
Fuel tank may be in an unstable condition because of the shape of fuel tank bottom. Never rely on jack too much. Be sure to hold tank securely.

INSTALLATION

Note the following, and install in the reverse order of removal.

Fuel Filler Hose
• Insert fuel filler hose to the length below.

: 35 mm (1.38 in)

• Be sure hose clamp is not placed on swelled area of fuel filler tube.

• Tighten fuel filler hose clamp so that the remaining length of screw thread becomes to the following.

Fuel filler tube side : 7 - 11 mm (0.28 - 0.43 in) Fuel tank side : 5 - 9 mm (0.20 - 0.35 in)

EVAP Hose
1. Check connections for damage or foreign material. 2. Align the matching side connection part with the center of shaft, and insert connector straight until it clicks.

3. After connecting, pull out quick connector and centralized underfloor piping by hand. Make sure connections are secure.

A : Pull

4WD : Inspection

4WD : Inspection

INSPECTION AFTER INSTALLATION

Use the following procedure to check for fuel leakage.

1. Turn ignition switch “ON” (with engine stopped), and check connections for leakage by applying fuel pressure to fuel piping.

2. Start engine and rev it up and check there are no fuel leakage at the fuel system tube and hose connections.