Body Repair

Replacement operations

In this manual: Body Repair
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~15min read

Description

• This section is prepared for technicians who have attained a high level of skill and experience in repairing collision-damaged vehicles and also use modern service tools and equipment. Persons unfamiliar with body repair techniques should not attempt to repair collision-damaged vehicles by using this section. • Technicians are also encouraged to read the Body Repair Manual (Fundamentals) in order to ensure that the original functions and quality of the vehicle are maintained. The Body Repair Manual (Fundamentals) contains additional information, including cautions and warnings, that are not including in this manual. Technicians should refer to both manuals to ensure proper repair.

• Please note that this information is prepared for worldwide usage, and as such, certain procedures might not apply in some regions or countries.

The symbols used in this section for welding operations are shown below.

• Front pillar butt joint can be determined anywhere within shaded

• Front pillar butt joint can be determined anywhere within shaded area as shown in the figure. The best location for the butt joint is at position A due to the construction of the vehicle.

• Determine cutting position and record distance from the locating

• Determine cutting position and record distance from the locating indent. Use this distance when cutting the service part. Cut outer front pillar over 60 mm (2.36 in) above the inner front pillar cut position.

• Prepare a cutting jig to make outer pillar easier to cut. Also, this will

• Prepare a cutting jig to make outer pillar easier to cut. Also, this will permit the service part to be accurately cut at the joint position.

• An example of cutting operation using a cutting jig is as per the

• An example of cutting operation using a cutting jig is as per the following.

1. Mark cutting lines.

A: Cut position of outer pillar B: Cut position of inner pillar 2. Align cutting line with notch on jig. Clamp jig to pillar. 3. Cut outer pillar along groove of jig (at position A). 4. Remove jig and cut remaining portions.

5. Cut inner pillar at position B in same manner.

Radiator Core Support

Radiator Core Support

Vehicle front

Replacement partsVehicle front


Replacement parts
● Side radiator core support (LH Upper) ● Side radiator core support (LH Lower)
● Hoodledge connector (LH)

Hoodledge (RHD Models)

Work after radiator core support is removed.

Vehicle front

Replacement partsVehicle front


Replacement parts
● Front strut housing (LH) ● Hoodledge reinforcement (LH)

View B: Before installing hoodledge reinforcement

Hoodledge (LHD Models)

Work after radiator core support is removed

Vehicle front

Replacement partsVehicle front


Replacement parts ● Front strut housing (LH) ● Hoodledge reinforcement (LH)

View B: Before installing hoodledge reinforcement

Hoodledge (RHD Models Partial Replacement)

Work after radiator core support is removed.

Remove the welding points ″f″ for easier installation.

Vehicle front

Replacement partsVehicle front


Replacement parts
● Upper hoodledge (RH) ● Lower front hoodledge (RH) ● Hoodledge reinforcement (RH)

View B: Before installing hoodledge reinforcement

Unit: mm (in)

Unit: mm (in)
View D: Before installing hoodledge reinforcement: Vehicle front


View D: Before installing hoodledge reinforcement

Hoodledge (LHD Models Partial Replacement)

Work after radiator core support is removed.

Remove the welding points ″f″ for easier installation.

Vehicle front

Replacement partsVehicle front


Replacement parts
● Upper hoodledge (RH) ● Lower front hoodledge (RH) ● Hoodledge reinforcement (RH)

View B: Before installing hoodledge reinforcement

Unit: mm (in)

Unit: mm (in)
View D: Before installing hoodledge reinforcement: Vehicle front


View D: Before installing hoodledge reinforcement

Front Side Member (2WD, RHD Models)

Work after radiator core support and hoodledge are removed.

: Vehicle front

: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

Replacement parts
● Front side member assembly (LH) ● Front suspension mounting bracket (LH Front)
● Engine mounting reinforcement ● Front side member reinforcement assembly
● Tie down hook reinforcement ● Front side member closing plate assembly (LH)
● Front towing hook reinforcement ● Add on frame bracket (LH) ● Front tie down hook ● Sensor harness bracket (LH) ● Front brake hose bracket (LH) ● Front suspension mounting bracket (LH Rear)

: Vehicle front

: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

View G: Before installing front suspension mounting bracket (Rear)

Unit: mm (in)

Unit: mm (in)
: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

View M: Before installing front suspension mounting bracket (Rear)

Front Side Member (2WD, LHD Models)

Work after radiator core support and hoodledge are removed.

: Vehicle front

: Vehicle front
: Weld the parts onto the back of the component part.

Replacement parts
● Front side member assembly (LH) ● Front suspension mounting bracket (LH Front)
● Engine mounting reinforcement ● Front side member reinforcement assembly
● Tie down hook reinforcement ● Front side member closing plate assembly (LH)
● Front towing hook reinforcement ● Add on frame bracket ● Front tie down hook ● Sensor harness bracket (LH) ● Front brake hose bracket (LH) ● Front suspension mounting bracket (LH Rear)

: Vehicle front

: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

View G: Before installing front suspension mounting bracket (Rear)

Unit: mm (in)

Unit: mm (in)
: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

View M: Before installing front suspension mounting bracket (Rear)

Front Side Member (4WD, RHD Models)

Work after radiator core support and hoodledge are removed.

: Vehicle front

: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

Replacement parts
● Front side member assembly (LH) ● Front side member closing plate assembly (LH)
● Front suspension mounting bracket (LH Rear)

: Vehicle front

: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

View D and H: Before installing front suspension mounting bracket (Rear)

Front Side Member (4WD, LHD Models)

Work after radiator core support and hoodledge are removed.

: Vehicle front

: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

Replacement parts
● Front side member assembly (LH) ● Front side member closing plate assembly (LH)
● Front suspension mounting bracket (LH Rear)

: Vehicle front

: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

View D and H: Before installing front suspension mounting bracket (Rear)

Front Side Member (2WD Models Partial Replacement)

Work after radiator core support is removed.

: Vehicle front

: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

Replacement parts
● Front suspension mounting bracket (RH Front)
● Add on frame bracket (RH)

POINT

The front side member on the left can also be replaced partially by butt welding.

Unit: mm (in)

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Front side member assembly (LH) ● Front side member closing plate assembly (LH)

NOTE

:
For welding method and the number of welding points, refer to BRM-50, "Front Side Member (2WD, RHD Models)" or BRM-53, "Front Side Member (2WD, LHD Models)".

Front Side Member (4WD Models Partial Replacement)

Work after radiator core support is removed.

: Vehicle front

: Vehicle front
: Weld the parts onto the back of the component part.

Replacement parts
● Front suspension mounting bracket (RH Front)
● Add on frame bracket (RH)

POINT

The front side member on the left can also be replaced partially by butt welding.

Unit: mm (in)

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Front side member assembly (LH) ● Front side member closing plate assembly (LH)

NOTE

:
For welding method and the number of welding points, refer to BRM-56, "Front Side Member (4WD, RHD Models)" or BRM-58, "Front Side Member (4WD, LHD Models)".

Front Pillar (RHD Models)

Work after hoodledge reinforcement is removed.

1. Body sealing

1. Body sealing

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Outer front side body (LH) ● Front pillar brace (LH) ● Side dash (LH) ● Upper inner front pillar (LH) ● Front fender bracket assembly (LH)

View A: Before installing outer front side body, front fender bracket assembly, and front pillar brace

1. Urethane foam

1. Urethane foam

: Drill φ9 mm (0.35 in) hole for: Vehicle front
the plug welding hole (ultra high strength steel plate).: Drill φ9 mm (0.35 in) hole for
the plug welding hole (ultra high strength steel plate).

the component part.: Weld the parts onto the back of
the component part.

View E: Before installing outer front side body and front fender bracket assembly
View G: Before installing outer front side body, front fender bracket assembly, and front pillar brace

Unit: mm (in)

Unit: mm (in)
View N: Before installing outer front side body: Vehicle front


View N: Before installing outer front side body

Front Pillar (LHD Models)

Work after hoodledge reinforcement is removed.

1. Body sealing

1. Body sealing

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Outer front side body (LH) ● Front pillar brace (LH) ● Side dash (LH) ● Upper inner front pillar (LH) ● Front fender bracket assembly (LH)

View A: Before installing outer front side body, front fender bracket assembly, and front pillar brace

1. Urethane foam

1. Urethane foam

View E: Before installing outer front side body and front fender bracket: Vehicle front


View E: Before installing outer front side body and front fender bracket assembly

Unit: mm (in)

Unit: mm (in)
: Drill φ9 mm (0.35 in) hole for: Vehicle front
the plug welding hole (ultra high strength steel plate).: Drill φ9 mm (0.35 in) hole for
the plug welding hole (ultra high strength steel plate).

the component part.: Weld the parts onto the back of
the component part.

View G: Before installing outer front side body, front fender bracket assembly, and front pillar brace View M: Before installing outer front side body

Center Pillar (2WD Models)

1. Outer sill reinforcement

1. Outer sill reinforcement 2. Lower center pillar brace 3. Inner center pillar

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Outer front side body (LH) ● Lower center pillar brace (LH) ● Inner center pillar (LH)

1. Outer sill reinforcement

1. Outer sill reinforcement 2. Lower center pillar brace

Unit: mm (in)
View B, D, E, and G: Before installing outer front side body: Vehicle front


View B, D, E, and G: Before installing outer front side body

Center Pillar (4WD Models)

1. Outer sill reinforcement

1. Outer sill reinforcement 2. Lower center pillar brace 3. Inner center pillar

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Outer front side body (LH) ● Lower center pillar brace (LH) ● Inner center pillar (LH)

1. Outer sill reinforcement

1. Outer sill reinforcement 2. Lower center pillar brace

Unit: mm (in)
View B, D, E, and G: Before installing outer front side body: Vehicle front


View B, D, E, and G: Before installing outer front side body

Outer Sill (Partial Replacement)

Unit: mm (in)

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Outer sill (LH) ● Outer sill reinforcement (LH)

View A: Before installing outer sill

Outer Sill (RHD Models)

1. Body sealing

1. Body sealing
2. Adhesive
3. Urethane foam

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Outer sill (LH) ● Outer sill reinforcement (LH) ● Front fender bracket assembly (LH)

View B: Before installing outer sill

1. Hemming portion

1. Hemming portion

Unit: mm (in)
View J: Before installing outer sill: Vehicle front


View J: Before installing outer sill POINT

• Perform the hemming to the flange of wheelarch after applying the adhesive. • Apply the sealing to the flange end.

• Refer to BRM-40, "Rear Fender Hemming Process".

1. Outer rear wheelhouse 2. Rear fender
3. Adhesive
4. Sealant

Outer Sill (LHD Models)

Outer Sill (LHD Models)

1. Body sealing

1. Body sealing
2. Adhesive
3. Urethane foam

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
• Outer sill (LH) • Outer sill reinforcement (LH) •

Front fender bracket assembly (LH)

View B: Before installing outer sill

1. Hemming portion

1. Hemming portion

Unit: mm (in)
View J: Before installing outer sill: Vehicle front


View J: Before installing outer sill POIN

• Perform the hemming to the flange of wheelarch after applying the adhesive. • Apply the sealing to the flange end.

• Refer to BRM-40, "Rear Fender Hemming Process".

1. Outer rear wheelhouse 2. Rear fender
3. Adhesive
4. Sealant

Inner Sill

Inner Sill

Work after outer sill is removed.

Remove the lower front pillar hinge brace (reusable).

1. Lower front pillar hinge brace

1. Lower front pillar hinge brace

Unit: mm (in)
: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

Replacement parts
● Inner sill (LH)

Unit: mm (in)

Unit: mm (in)
: Weld the parts onto the back of Vehicle front
the component part.: Weld the parts onto the back of
the component part.

View D: Before installing lower front pillar hinge brace

Rear Fender (2WD Models)

1. Urethane foam

1. Urethane foam
2. Body sealing
3. Adhesive
4. Hemming portion

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Rear fender (LH) ● Rear fender extension (LH) ● Rear fender corner (LH) ● Striker retainer ● Fuel filler base (Right side rear fender)

1. Adhesive

1. Adhesive

Unit: mm (in)
: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

View F: Before installing rear fender View H: Right side rear fender

POINT

• Perform the hemming to the flange of wheelarch after applying the adhesive. • Apply the sealing to the flange end.

• Refer to BRM-40, "Rear Fender Hemming Process".

1. Outer rear wheelhouse 2. Rear fender
3. Adhesive
4. Sealant

Rear Fender (4WD Models)

Rear Fender (4WD Models)

1. Urethane foam

1. Urethane foam
2. Body sealing
3. Adhesive
4. Hemming portion

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Rear fender (LH) ● Rear fender extension (LH) ● Rear fender corner (LH)

1. Adhesive

1. Adhesive

Unit: mm (in)
: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

View F: Before installing rear fender View H: Right side rear fender

POINT

• Perform the hemming to the flange of wheelarch after applying the adhesive. • Apply the sealing to the flange end.

• Refer to BRM-40, "Rear Fender Hemming Process".

1. Outer rear wheelhouse 2. Rear fender
3. Adhesive
4. Sealant

Rear Fender Extension (2WD Models)

Rear Fender Extension (2WD Models)

1. Body sealing

1. Body sealing

Replacement parts
● Rear fender corner (LH

Rear Fender Extension (4WD Models)

1. Body sealing

1. Body sealing

Replacement parts
● Rear fender corner (LH)

Rear Pillar Reinforcement

Work after rear fender is removed.

Unit: mm (in)

Unit: mm (in)
: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

Replacement parts
● Inner rear pillar reinforcement (LH)

Outer Rear Wheelhouse (2WD Models)

Work after rear fender is removed.

Remove the outer sill reinforcement (reusable) for easier installation.

1. Outer sill reinforcement

1. Outer sill reinforcement

Replacement parts: Vehicle front


Replacement parts
● Outer rear wheelhouse (LH)

1. Outer sill reinforcement

1. Outer sill reinforcement

Unit: mm (in)
View C: Before installing outer sill reinforcement: Vehicle front


View C: Before installing outer sill reinforcement

Outer Rear Wheelhouse (4WD Models)

Work after rear fender is removed.

Remove the outer sill reinforcement (reusable) for easier installation.

1. Outer sill reinforcement

1. Outer sill reinforcement

Replacement parts: Vehicle front


Replacement parts
● Outer rear wheelhouse (LH)

1. Outer sill reinforcement

1. Outer sill reinforcement

Unit: mm (in)
View C: Before installing outer sill reinforcement: Vehicle front


View C: Before installing outer sill reinforcement

Inner Rear Wheelhouse (2WD Models)

Work after rear fender, outer sill reinforcement, and outer rear wheelhouse are removed

Unit: mm (in)

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Inner rear wheelhouse (LH)

Inner Rear Wheelhouse (4WD Models)

Work after rear fender, outer sill reinforcement, and outer rear wheelhouse are removed.

Unit: mm (in)

Unit: mm (in)
Replacement parts: Vehicle front


Replacement parts
● Inner rear wheelhouse (LH)

Rear Panel (2WD Models)

Unit: mm (in)

Unit: mm (in)
: Welding method and the number of: Vehicle front
welding points apply to both side of the vehicle.: Welding method and the number of
welding points apply to both side of the vehicle.

Replacement parts
● Upper rear panel

Rear Panel (4WD Models)

Unit: mm (in)

Unit: mm (in)
: Welding method and the number of: Vehicle front
welding points apply to both side of the vehicle.: Welding method and the number of
welding points apply to both side of the vehicle.

Replacement parts
● Upper rear panel

Inner Rear Pillar

Work after rear fender and inner rear pillar reinforcement are removed.

: Vehicle front

: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

Replacement parts
● Inner rear pillar (LH) ● Rear pillar reinforcement (LH)

Rear Floor Rear (2WD Models)

Work after rear panel is removed.

: Vehicle front

: Welding method and the number of: Vehicle front
welding points apply to both side of the vehicle.: Welding method and the number of
welding points apply to both side of the vehicle.

the component part.: Weld the parts onto the back of
the component part.

Replacement parts
● Rear floor rear ● Spare tire clamp bracket ● Rear towing hook bracket ● Muffler mounting bracket

Rear Floor Rear (4WD Models)

Work after rear panel is removed.

: Vehicle front

: Welding method and the number of: Vehicle front
welding points apply to both side of the vehicle.: Welding method and the number of
welding points apply to both side of the vehicle.

Replacement parts
● Rear floor rear ● Spare tire clamp bracket ● Jack mounting bracket ● Canister bracket

Rear Side Member (4WD Models Partial Replacement)

Work after rear panel and rear floor rear are removed.

Unit: mm (in)

Unit: mm (in)
: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

Replacement parts
● Rear side member assembly (LH)

Rear Side Member Extension (2WD Models)

Work after rear panel is removed.

Vehicle front

: Weld the parts onto the back ofVehicle front
the component part.: Weld the parts onto the back of
the component part.

Replacement parts
● Rear side member extension (LH)

Rear Side Member Extension (4WD Models)

Work after rear panel is removed.

: Vehicle front

: Weld the parts onto the back of: Vehicle front
the component part.: Weld the parts onto the back of
the component part.

Replacement parts
● Rear side member extension (LH)

Roof

1. Body sealing

1. Body sealing

: Welding method and the number of: Vehicle front
welding points apply to both side of the vehicle.: Welding method and the number of
welding points apply to both side of the vehicle.

side of the vehicle.: Sealing portion apply to both
side of the vehicle.

Replacement parts
● Roof ● Roof bow No. 1 ● Roof bow No. 2 ● Roof bow No. 3

Roof Rail

Work after roof is removed.

1. Adhesive

1. Adhesive

: Welding method and the number of: Vehicle front
welding points apply to both side of the vehicle.: Welding method and the number of
welding points apply to both side of the vehicle.

side of the vehicle.: Adhesive portion apply to both
side of the vehicle.

Replacement parts
● Front roof rail ● Rear roof rail