Tail lamp circuit
Without daytime running light system
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function 1.CHECK TAIL LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the tail lamp is turned ON.
TAIL : Tail Lamp ON
Off : Tail lamp OFF
Is the inspection result normal? YES >> Tail lamp circuit is normal.
NO >> Refer to EXL-61, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure".
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure 1.CHECK TAIL LAMP BULBCheck the applicable lamp bulb.
Is the inspection result normal? YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK PARKING LAMP OPERATIONCheck that the parking lamp is turned ON.
Is the inspection result normal? YES-1 (When tail lamp (RH) does not turn ON.)>>GO TO 6.YES-2 (When tail lamp (LH) does not turn ON.)>>GO TO 3.
NO >> Check parking lamp circuit. Refer to EXL-58, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check".
3.CHECK TAIL LAMP (LH) FUSE 1. Turn ignition switch OFF.2. Check that the following fuses are not fusing

Is the inspection result normal? YES >> GO TO 4.
NO >> GO TO 5.
4.CHECK TAIL LAMP (LH) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect rear combination lamp (LH) connector. 2. Turn ignition switch ON. 3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4. With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal? YES >> GO TO 6.
NO >> Replace IPDM E/R.
5.CHECK TAIL LAMP (LH) SHORT CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect IPDM E/R connector and rear combination lamp (LH) connector.3. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal? YES >> Replace fuse. (Replace IPDM E/R if fusing is found again.) NO >> Repair or replace harness. And then replace the fuse.
6.CHECK TAIL LAMP OPEN CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect IPDM E/R connector and rear combination lamp connector.3. Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.

Is the inspection result normal? YES >> GO TO 7.
NO >> Repair or replace harness.
7.CHECK TAIL LAMP GROUND OPEN CIRCUITCheck continuity between rear combination lamp harness connector and ground.

Is the inspection result normal? YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
With daytime running light system
WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check 1.CHECK TAIL LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the tail lamp is turned ON.
TAIL : Tail Lamp ON
Off : Tail lamp OFF
Is the inspection result normal? YES >> Tail lamp circuit is normal.
NO >> Refer to EXL-63, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure".
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure 1.CHECK TAIL LAMP BULBCheck the applicable lamp bulb.
Is the inspection result normal? YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK PARKING LAMP OPERATIONCheck that the parking lamp is turned ON.
Is the inspection result normal? YES-1 (When tail lamp (RH) does not turn ON.)>>GO TO 4.YES-2 (When tail lamp (LH) does not turn ON.)>>GO TO 3.
NO >> Check parking lamp circuit. Refer to EXL-59, "WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check".
3.CHECK TAIL LAMP (LH) SHORT CIRCUIT 1. Turn ignition switch OFF. 2. Remove daytime running light relay. 3. Disconnect rear combination lamp (LH) connector.4. Check continuity between daytime running light relay harness connector and ground.

Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK TAIL LAMP OPEN CIRCUIT 1. Turn ignition switch OFF. 2. Remove daytime running light relay. 3. Disconnect rear combination lamp connector.4. Check continuity between daytime running light relay harness connector and rear combination lamp harness connector.

Is the inspection result normal? YES >> GO TO 5.
NO >> Repair or replace harness.
5.CHECK TAIL LAMP GROUND OPEN CIRCUIT Check continuity between rear combination lamp harness connector and ground.

Is the inspection result normal? YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.