Transmission & Driveline

Front Drive Shaft

4steps
~24min
5/5difficulty
0204060801004835N·mlb·ft
Tightening torque found on this page
Done 0 of 4
Exploded View (LH)
1. Drive shaft 2. Nut retainer 3. Cotter pin
Removal and Installation (LH)

REMOVAL

Remove disc brake rotor. Refer to Removal and Installation.

Remove wheel sensor bolt (A) and position wheel sensor aside. Refer to Exploded View.

Remove cotter pin.

Remove nut retainer.

Loosen wheel hub lock nut from drive shaft using power tool.

Using a piece of wood and a suitable tool, tap on wheel hub lock nut to disengage drive shaft from wheel hub and bearing.

Remove wheel hub lock nut.

Remove lower strut bolts and nuts.

Separate front strut from steering knuckle. Refer to Exploded View.

Separate drive shaft from wheel hub and bearing. Reposition drive shaft aside with wire.

Set Tool (A)between drive shaft (slide joint side) and transaxle as shown. Remove drive shaft.

Tool number : Drive shaft joint puller (Commercially available)

Remove differential side oil seal. Refer to Removal and Installation.

INSPECTION AFTER REMOVAL

  • Move joint up/down, left/right, and in axial direction. Check for any rough movement or significant looseness.

  • Check boot for cracks or other damage and for grease leakage.

  • If damaged, disassemble drive shaft to verify damage, and repair or replace as necessary.

INSTALLATION

Install new differential side oil seal. Refer to Removal and Installation.

Install new circular clip on drive shaft in circular clip groove on transaxle side. Refer to Exploded View (LH).

In order to prevent damage to differential side oil seal, place Tool (A) onto oil seal before inserting drive shaft as shown. Slide drive shaft into slide joint and tap with a suitable tool to install securely.

Tool number : KV38107900 (J–52469–1)

  • To ensure the circular clip is properly engaged, grasp the housing (1) and pull back and forth in axial direction while listening for clicking sounds.

  • Pull the joint sub-assembly in the axial direction away from transaxle assembly (arrow). Confirm that the joint sub assembly cannot be pulled out.

Clean mating surfaces of wheel hub lock nut and wheel hub and bearing.

Tighten wheel hub lock nut to specification. Refer to Exploded View (LH).

When installing cotter pin (1) and nut retainer (2), securely bend cotter pin to prevent rattles.

Remainder of installation is in reverse order of removal.

INSPECTION AND ADJUSTMENT AFTER INSTALLATION

Check CVT fluid level and leakage. Refer to Inspection.

Check wheel alignment. Refer to Inspection.

Adjust neutral position of the steering angle sensor. Refer to Description.

Exploded View (RH)
1. Cotter pin 2. Nut retainer 3. Drive shaft
4. Bearing retainer 5. Support bearing bracket A. Refer to Removal and Installation.
Removal and Installation (RH)

REMOVAL

Remove disc brake rotor. Refer to Removal and Installation.

Remove wheel sensor bolt (A) and position wheel sensor aside. Refer to Exploded View.

Remove cotter pin.

Remove nut retainer.

loosen wheel hub lock nut from drive shaft using power tool.

Using a piece of wood and a suitable tool, tap on wheel hub lock nut to disengage drive shaft from wheel hub and bearing.

Remove wheel hub lock nut.

Remove lower strut bolts and nuts.

Separate front strut from steering knuckle. Refer to Exploded View.

Remove bearing retainer to support bearing bracket bolts.

Remove bearing retainer.

Set Tool (A) between drive shaft (slide joint side) and transaxle as shown. Remove drive shaft.

Tool number (A) : Drive shaft joint puller (Commercially available)

If necessary, remove support bearing bracket bolts and bracket.

For AWD models, remove the drive shaft oil seal using the following procedure:Remove the bolts and the support bearing bracket. Using a suitable tool, remove the transfer cover oil seal.

Remove the drive shaft oil seal (1) using suitable tool (A).

For FWD Nissan Murano vehicles, remove differential side oil seal. Refer to Removal and Installation.

INSPECTION AFTER REMOVAL

  • Move joint up/down, left/right, and in axial direction. Check for any rough movement or significant looseness.

  • Check boot for cracks or other damage and for grease leakage.

  • If damaged, disassemble drive shaft to verify damage, and repair or replace as necessary.

INSTALLATION

For AWD models, install the drive shaft oil seal and transfer cover oil seal using the following procedure:Install drive shaft oil seal (1) onto Tool (A) before installing into transfer case assembly using Tool (B).

Tool (A) : — (J-52390)
Tool (B) : — (J-8092)

Using two people, install the drive shaft oil seal (1) to the specified depth (A).

Dimension (A) : 2.0 - 2.6 mm (0.079 - 0.102 in)

Using two people, install the transfer cover oil seal (1) using suitable tool (A).
Verify the transfer cover oil seal (2) is installed to the correct depth (A).

Dimension (A) : 0.0 - 0.6 mm (0.000 - 0.024 in)

(1) : Drive shaft oil seal
(B) : Drive shaft oil seal installation depth

Lubricate the transfer cover oil seal and drive shaft oil seal lips before installing front drive shaft (RH).

Install support bearing bracket.

  • Tighten support bearing bracket bolts in numerical order as shown.

  • Refer to following for installation positions of bolts.

M10 bolt No. 1 - 4: 48 N·m

: Front

For FWD models, install a new differential side oil seal. Refer to Removal and Installation.

Install new circular clip on drive shaft in circular clip groove on transaxle side. Refer to Exploded View (RH).

In order to prevent damage to differential side oil seal, place Tool (A) onto oil seal before inserting drive shaft as shown. Slide drive shaft into slide joint and tap with a hammer to install securely.

Tool number : KV38107900 (J–52469–1)

  • To ensure the circular clip is properly engaged, grasp the housing (1) and pull back and forth in axial direction while listening for clicking sounds.

  • Pull the joint sub-assembly in the axial direction away from transaxle assembly (arrow). Confirm that the joint sub assembly cannot be pulled out.

Install bearing retainer.

  • Tighten bearing retainer bolts in numerical order shown.

M8 bolt No. 1 and No. 2: 25 N·m

: Front

Clean mating surfaces of wheel hub lock nut and wheel hub and bearing.

Tighten wheel hub lock nut to specification. Refer to Exploded View (RH).

When installing cotter pin (1) and nut retainer (2), securely bend cotter pin to prevent rattles.

Installation of remaining components is in reverse order of removal.

INSPECTION AND ADJUSTMENT AFTER INSTALLATION

  1. For FWD vehicles, check CVT fluid level and leakage. Refer to Inspection.

  2. For AWD Nissan Murano vehicles, check transfer case fluid level. Refer to Inspection.

  3. Check wheel alignment. Refer to Inspection.

  4. Adjust neutral position of the steering angle sensor. Refer to Description.