Transmission & Driveline

Front Wheel Drive

~10min read
010203040502015N·mlb·ft
Tightening torque found on this page
Removal and Installation - FWD

Removal

Remove starter. Refer to Removal and Installation.

Remove the cowl top cover and the cowl top extension. Refer to cowl top cover Removal and Installation and cowl top extension Removal and Installation - Cowl Top Extension.

Remove lock plate (1) as shown.

Remove nut (A) and separate control cable (1) from the manual lever (B).

Disconnect the harness connector (A) from the transmission range switch (1).

Disconnect brake booster vacuum hose from intake manifold collector. Refer to Exploded View.

Release clamp and disconnect PCV hose (1) from intake manifold collector (2).

Remove bolts (A) and set VIAS control solenoid valves (1) aside.

Disconnect vacuum hoses (1) from intake manifold collector (2).

Disconnect vacuum hose (1) from vacuum pipe (2).

Remove bolt (A).

Remove clamp (1) and disconnect hose (2) from pipe (3).

Release pawl and remove hose (4) from retainer (A).

: Pawl

Remove bolt (B) and set EVAP canister purge volume control solenoid (5) aside.

Remove bolts (A) and set vacuum tube assembly (1) aside.

Loosen bolts in reverse of sequence shown and remove electric throttle control actuator bolts, then remove electric throttle control actuator and position aside.

Remove bolt (A) and set O2 sensor harness bracket (1) aside.

Loosen the intake manifold collector bolts and nuts in reverse of the sequence shown, then remove the intake manifold collector and gasket.

Disconnect transaxle breather hose (1) from transaxle assembly.

Remove bolt (A) from upper torque rod.

Remove fuel tube bolts (A).

Remove CVT gusset bolt (A).

Remove bolts (A).

Remove nuts (A) and bracket (1).

Install Tool (B) using bolts (A) and (C) supplied with Tool. Tighten bolts to specification. Refer to Engine Support Tool Operating Instructions.

Tool (B) : (J-52604)
Bolts (A) : 20 N·m
Bolts (C) : 11 N·m

Install Tool (A) to drivers side frame rail (1) as shown. Refer to Engine Support Tool Operating Instructions.

Tool (A) : (J-52389)

Install Tool (A) on top of engine mounting insulator [RH (1)] as shown. Refer to Engine Support Tool Operating Instructions.

Tool (A) : (J-52389)

Install Tool (A) to Tool (B). Refer to Engine Support Tool Operating Instructions.

Tool (A) : (J-52389)
Tool (B) : (J-52604)

Using bubble level (B) on Tool (A) level Tool as shown. Refer to Engine Support Tool Operating Instructions.

Tool (A) : (J-52389)

Remove nut from engine mounting insulator (front). Refer to Exploded View.

Remove nut from engine mounting insulator (rear). Refer to Exploded View.

Remove the front wheels and tires using power tool (LH/RH).

Remove brake hose retaining clip and brake hose from strut (LH/RH).

Remove brake caliper torque member bolts using power tool, leaving hydraulic hose attached to the brake caliper. Position the brake caliper aside with wire (LH/RH). Refer to Exploded View.

Put alignment marks (A) on the disc brake rotor and on the wheel hub and bearing, then remove disc brake rotor (LH/RH).

Remove wheel sensor bolt (A) and position wheel sensor aside (LH/RH).

Remove and discard cotter pin from front drive shaft (LH/RH).

Remove nut retainer from drive shaft (LH/RH).

Loosen the wheel hub lock nut from the drive shaft using power tool (LH/RH).

Remove front strut to steering knuckle bolts and nuts, then separate front strut from steering knuckle (LH/RH). Refer to Exploded View.

Using a piece of wood and a suitable tool, tap on the wheel hub lock nut to disengage the drive shaft from the wheel hub and bearing (LH/RH).

Remove the wheel hub lock nut (LH/RH).

Remove bearing retainer to support bearing bracket bolts and remove bearing retainer (RH only).

Insert suitable tool (A) between the drive shaft and transaxle. Remove the drive shaft from the transaxle (LH/RH).

Tool (A) : Drive shaft joint puller (Commercially available)

Remove the differential side oil seal (LH/RH).

Remove nut and separate stabilizer connecting rods from struts (LH/RH). Refer to Exploded View.

Remove outer socket cotter pins (LH/RH). Refer to Exploded View.

Loosen the outer socket nuts and separate outer sockets from the steering knuckles (LH/RH) using ball joint remover (commercially available).

Remove the outer socket nuts and separate the outer sockets from the steering knuckles (LH/RH).

Remove front under cover. Refer to Exploded View.

Remove the front half of front over fenders (LH/RH). Refer to Exploded View.

Remove engine side cover (LH/RH). Refer to Exploded View.

Remove the front half of front fender protectors (LH/RH). Refer to Exploded View.

Remove bolt (A) and position crankshaft position sensor (1) aside.

Remove the front exhaust tube. Refer to Exploded View.

Disconnect the front engine mount insulator vacuum hose (1).

Remove bolt (A) and remove rear cover plate (1).

Remove torque converter nuts. Refer to Exploded View.

Remove the power steering tube bracket bolts. Refer to Exploded View.

Remove the bolts and nuts from the steering gear. Refer to Exploded View.

Secure the steering gear using suitable wire.

Remove bolts (A) from transaxle mount.

Remove bolt (A) and position ground (1) aside.

Remove water hose (1) from retainer (A).

Remove rear torque rod bolt. Refer to Exploded View.

Set hydraulic lift table (A) or equivalent tool under front suspension member.

Remove front suspension member bolts and front suspension member stays. Refer to Exploded View.

Lower the front suspension member.

Remove bolt from heater thermostat bracket. Refer to Exploded View.

Drain engine coolant. Refer to Changing Engine Coolant.

Remove CVT fluid cooler hose A and CVT fluid cooler hose B from the CVT oil warmer. Refer to Exploded View.

Remove CVT water hose A and CVT water hose B from CVT oil warmer. Refer to Exploded View.

Using Tools lower engine and transaxle assembly until the transaxle assembly is low enough to clear driver’s side frame rail.

Tool numbers : (J-52389, J-52604)

Release the harness retainers from the transaxle assembly.

Disconnect the harness connector (A) from the transaxle assembly.

Disconnect the harness connector from the output speed sensor. Refer to Exploded View.

Disconnect the harness connector from the primary speed sensor. Refer to Exploded View.

Disconnect the harness connector from the input speed sensor. Refer to Exploded View.

Support transaxle assembly using a suitable transmission jack and Tool.

Tool number : (J-51307)

Remove bolts (A), (B), (C), and (D).

Separate the transaxle assembly from the engine assembly and lower transaxle assembly.

INSTALLATION

Installation is in the reverse order of removal.

If replacing CVT, flush the CVT fluid cooler and lines. Refer to CVT Fluid Cooler Flush.

Perform inspection before installation. Refer to "Inspection Before Installation" below.