Renault Megane Quiz
Chassis

Configurations and teachings

In this manual: Chassis
Engine and peripherals — 141Chassis — 79Chassis — 72Renault Mégane III Driver's Manual — 87Electrical equipment — 221Engine and peripherals — 47Electrical equipment — 80Transmission — 14Air conditioning — 30Bodywork — 115Trim and upholstery — 44General vehicle information — 27Air conditioning — 59General vehicle information — 16Transmission — 38Sealing and soundproofing — 7General vehicle information — 3
~4min read

SC002: TEACHING THE CODES OF THE FOUR VALVES

WARNING: Any operation requiring replacement of a wheel sensor requires full knowledge of the recommendations defined in Repair Manual 364, chapter 35.
  • Inflate all 4 wheels to 3.8 bar.
  • Establish communication with the Cabin Central Unit (UCH) using the diagnostic tool.
  • Select the "repair mode" menu.
  • Select the "teaching" menu.
  • Select line SC002 "Teaching the codes of the four valves" in the "tyre" function.
  • Display the stored codes and the set of recognised valves.
  • Select the "valve set selection" menu, then "summer" or "winter".
  • Confirm to display the "valve teaching conditions" table.
  • Confirm by selecting "next" to display the "valve code search" menu.
  • Activate each valve by holding the valve trigger tool against the tyre, just below the valve concerned.
  • Start with the front left wheel.
  • Wait for the new code to appear on the screen, then move on to the next valve.
  • The order for teaching the codes is as follows:
    Front left → Front right → Rear right → Rear left
  • Click the "confirm" button to transfer the codes to the Cabin Central Unit (UCH).
  • Inflate the tyres to the recommended pressure.
  • Carry out a road test: speed > 20 km/h for 10 minutes.
  • Make sure no message appears on the instrument panel.
WARNING:

For any wheel rotation, use the diagnostic tool to teach the Cabin Central Unit (UCH) the new valve positions by running a valve code teaching.

Replace the colour rings at the location shown on the label on the driver's door.

SC001: READING THE VALVE SET AND STORED CODES

  • Select the "repair mode" menu.
  • Select the "learning" menu.
  • Select line SC001 "Reading the valve set and stored codes" in the "tyre pressure" function.

VP005: ENTERING RECOMMENDED PRESSURES

To correctly enter the recommended pressures, use the manufacturer's recommended pressures from the repair manual, the vehicle owner's handbook for the tyres fitted to the vehicle, or those noted on the label on the driver's door.
  • Select the "repair mode" menu.
  • Select the "other settings" menu.
  • Select line VP005 "Entering recommended pressures".
  • Use the keypad to enter the recommended pressures.
  • Confirm the pressures.
  • Click "Finish" to end the procedure.

Checking that the recommended pressures have been stored:

  • Select the "states / parameters" menu.
  • Select the "Tyre management" menu.
  • Read parameters PR009 to PR012.
  • If there is a problem, restart the operation from the beginning.

CF023: TPMS FUNCTION

WRITING THE CONFIGURATION WITH OR WITHOUT TPMS:
  • Select the "repair mode" menu.
  • Select the "learning" menu.
  • Select line CF023 "TPMS function", then "with" or "without".

    Confirm the selection.

  • Check that the configuration has been correctly stored in the "reading configuration" menu at line LC017: "TPMS function".
WARNING:

CONFIGURATION INCONSISTENCY INSTRUMENT PANEL / PASSENGER COMPARTMENT CONTROL UNIT

Case 1: - The instrument panel detects that the Tyre Pressure Monitoring System is programmed in the passenger compartment control unit but not in its own configuration. The message "ELECTRONIC FAULT" is then displayed, the 4 wheels disappear from the instrument panel and the "service" warning light comes on.

Case 2: - The instrument panel detects that the Tyre Pressure Monitoring System is programmed in its own configuration but the passenger compartment control unit does not respond to any request from the instrument panel (not configured in the passenger compartment control unit). The message "TYRE SENSOR FAULTY" is then displayed, the 4 wheels disappear from the instrument panel and the "service" warning light comes on.

INSTRUMENT PANEL CONFIGURATION

CF145: TYRE PRESSURE MONITORING

  • After the multiplexed network test, select "Instrument panel".
  • Select "repair mode".
  • Select "writing configurations".
  • Select line CF145 "Tyre pressure monitoring", then "with" or "without".
  • Confirm the selection.
  • Check that the configuration has been correctly stored in the "reading configuration" menu at line LC056: "Tyre pressure monitoring".

Test yourself

A quick Renault Megane quiz: every answer comes with an explanation and a link to the manual page.