Hybrid Transaxle Fluid
Components
COMPONENTS
ILLUSTRATION
*A |
Type A |
*B |
Type B |
*1 |
FRONT WHEEL OPENING EXTENSION PAD RH |
*2 |
FRONT WHEEL OPENING EXTENSION PAD LH |
*3 |
NO. 1 ENGINE UNDER COVER |
*4 |
NO. 2 ENGINE UNDER COVER ASSEMBLY |
*5 |
FILLER PLUG |
*6 |
DRAIN PLUG |
*7 |
GASKET |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
Replacement
REPLACEMENT
PROCEDURE
1. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
Click here ![]()
2. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
Click here ![]()
3. REMOVE NO. 1 ENGINE UNDER COVER
Click here ![]()
4. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
Click here ![]()
5. REPLACE HYBRID TRANSAXLE FLUID
(a) Lift the vehicle. [#1]
NOTICE:
Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).
(b) Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly. [#2] |
![]() |
(c) Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the hybrid vehicle transaxle assembly and drain the hybrid transaxle fluid. [#3] |
![]() |
(d) Using a 10 mm hexagon socket wrench, temporarily install the drain plug and gasket to the hybrid vehicle transaxle assembly. [#4]
HINT:
Reuse the old gasket as the drain plug will be removed again.
(e) Add hybrid transaxle fluid until the hybrid transaxle fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. [#5] NOTICE:
|
|
(f) Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly. [#6]
HINT:
Reuse the old gasket as the filler plug will be removed again.
(g) Lower the vehicle. [#7]
(h) Put the engine in Inspection Mode (Maintenance Mode). [#8]
Click here ![]()
(i) Idle the engine for 30 seconds with the power switch on (READY). [#9]
(j) Turn the power switch off. [#10]
(k) Repeat steps [#1] to [#10].
(l) Repeat steps [#1] to [#3].
(m) Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket to the hybrid vehicle transaxle assembly.
Torque:
50 N·m {510 kgf·cm, 37 ft·lbf}
(n) Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly.
HINT:
Reuse the old gasket as the filler plug will be removed again.
6. ADD HYBRID TRANSAXLE FLUID
Click here ![]()
7. INSPECT HYBRID TRANSAXLE FLUID
Click here ![]()
8. INSPECT FOR HYBRID TRANSAXLE FLUID LEAK
9. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY
Click here ![]()
10. INSTALL NO. 1 ENGINE UNDER COVER
Click here ![]()
11. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH
Click here ![]()
12. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH
Click here ![]()



