ECU Terminals
ECU TERMINALS
REAR VIEW CAMERA ASSY
(a) Disconnect the S11 rear view monitor camera assembly connector.
(b) Measure the voltage at each terminal of the connector on the wire harness side.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
S11-6 (CB+) - Body ground |
G - Body ground |
Power source |
Ignition Switch in ACC position |
5,5 à 7,05 V |
If the result is not as specified, there may be a malfunction in the wire harness.
(c) Reconnect the S11 rear view monitor camera assembly connector.
(d) Measure the resistance and check the pulses at each terminal of the connector.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
S11-3 (CV+) - S11-2 (CV-) |
W - R |
Video signal |
Ignition Switch in ON position Shift lever in R position The camera lens is not covered, an image is displayed |
Pulse generation (Refer to waveform 1) |
Ignition Switch in ON position Shift lever in R position Camera lens covered, blocking the screen |
Pulse generation (Refer to waveform 2) |
|||
S11-5 (CGND) - Body ground |
B - Body ground |
Camera ground |
Always |
Below 1 Ω |
HINT:
A waterproof connector is used for the rear view monitor camera assembly. Therefore, check the waveform at the radio and display receiver assembly with the connector connected.
If the result is not as specified, there may be a malfunction in the rear view monitor camera assembly.
(e) Reference (oscilloscope waveform):
*a |
Waveform 1 (camera lens not covered, image displayed) |
*b |
Waveform 2 (camera lens covered, screen obstructed) |
*c |
Sync signal |
*d |
Video waveform |
HINT:
A waterproof connector is used for the rear view monitor camera assembly. Therefore, check the waveform at the radio and display receiver assembly with the connector connected.
(1) Waveform 1 (camera lens not covered, image displayed)
Item | Content |
|---|---|
Test probe |
S11-3 (CV+) - S11-2 (CV-) |
Measurement setting |
200 mV/DIV., 50 µs./DIV. |
Condition |
Ignition switch ON, shift lever in R |
HINT:
- The video waveform changes depending on the image sent by the rear view camera assembly.
- The video waveform is output continuously when the ignition switch is in ON.
(2) Waveform 2 (camera lens covered, screen obstructed)
Item | Content |
|---|---|
Test probe |
S11-3 (CV+) - S11-2 (CV-) |
Measurement setting |
200 mV/DIV., 50 µs./DIV. |
Condition |
Ignition switch ON, shift lever in R |
HINT:
- The video waveform changes depending on the image sent by the rear view camera assembly.
- The video waveform is output continuously when the ignition switch is in ON.
RADIO AND DISPLAY RECEIVER ASSEMBLY
HINT:
Check from the rear of the connector while it is connected to the component parts.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F131-26 (CSLD) - Body ground |
Shield - Body ground |
Shield ground |
Always |
Below 1 V |
F131-27 (CGND) - Body ground |
B - Body ground |
Camera ground |
Always |
Below 1 V |
F131-28 (V+) - F129-1 (GND1) |
R - LA*1 W - LA*2 |
Video signal |
Ignition Switch in ON position Shift lever in R position The camera lens is not covered, an image is displayed |
Pulse generation (Refer to waveform 1) |
Ignition Switch in ON position Shift lever in R position Camera lens covered, screen obstructed |
Pulse generation (Refer to waveform 2) |
|||
F131-29 (V-) - F129-1 (GND1) |
W - LA*1 R - LA*2 |
Ground |
Always |
Below 1 V |
F131-30 (CA+) - F129-1 (GND1) |
G - LA |
Rear view camera assembly power supply |
Ignition Switch in ACC position |
5,5 à 7,05 V |
- *1: TMC made
- *2: TMMT made
(a) Reference (oscilloscope waveform):
(1) Waveform 1 (camera lens not covered, image displayed)
Item | Content |
|---|---|
Test probe |
F131-28 (V+) - F129-1 (GND1) |
Measurement setting |
200 mV/DIV., 50 µs./DIV. |
Condition |
Ignition switch ON, shift lever in R |
HINT:
- The video waveform changes depending on the image sent by the rear view camera assembly.
- The video waveform is output continuously when the ignition switch is in ON.
*a |
Waveform 1 (camera lens not covered, image displayed) |
*b |
Waveform 2 (camera lens covered, screen obstructed) |
*c |
Sync signal |
*d |
Video waveform |
(2) Waveform 2 (camera lens covered, screen obstructed)
Item | Content |
|---|---|
Test probe |
F131-28 (V+) - F129-1 (GND1) |
Measurement setting |
200 mV/DIV., 50 µs./DIV. |
Condition |
Ignition switch ON, shift lever in R |
HINT:
- The video waveform changes depending on the image sent by the rear view camera assembly.
- The video waveform is output continuously when the ignition switch is in ON.