Parking Assist / Monitor System

Rear View Camera Disconnected (C1622)

~4min read

DESCRIPTION

This DTC is stored if the radio and display receiver assembly determines, as a result of its self-diagnosis, that the signals or signal lines between the radio and display receiver assembly and the rear view camera assembly are abnormal.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

C1622

Rear view camera disconnected

Open or short circuit in rear view camera assembly

  • Wire harness or connector
  • Rear View Monitor Camera Assembly
  • Radio and Display Receiver Assembly

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly that was installed in another vehicle is reused, the following may occur:
    • A communication malfunction DTC is stored.
    • The radio and display receiver assembly may not operate normally.

PROCEDURE

  1. CHECK WIRE HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR VIEW CAMERA ASSEMBLY)

(a) Disconnect the F131 connector from the radio and display receiver assembly.

(b) Disconnect the S11 connector from the rear view camera assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F131-30 (CA+) - S11-6 (CB+)

Always

Below 1 Ω

F131-28 (V+) - S11-3 (CV+)

Always

Below 1 Ω

F131-29 (V-) - S11-2 (CV-)

Always

Below 1 Ω

F131-27 (CGND) - S11-5 (CGND)

Always

Below 1 Ω

F131-26 (CSLD) - Body ground

Always

Below 1 Ω

F131-30 (CA+) or S11-6 (CB+) - Body ground

Always

10 kΩ minimum

F131-28 (V+) or S11-3 (CV+) - Body ground

Always

10 kΩ minimum

F131-29 (V-) or S11-2 (CV-) - Body ground

Always

10 kΩ minimum

F131-27 (CGND) or S11-5 (CGND) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Reconnect the radio and display receiver assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F131-29 (V-) - Body ground

Always

Below 1 Ω

F131-27 (CGND) - Body ground

Always

Below 1 Ω

*a

Component with Wire Harness Connected

(Radio and Display Receiver Assembly)

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F131-30 (CA+) - F131-27 (CGND)

Ignition Switch in ACC position

5,5 à 7,05 V

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

OK
  1. INSPECT REAR VIEW MONITOR CAMERA ASSEMBLY

(a) Reconnect connector S11 of the rear view monitor camera assembly.

(b) Using an oscilloscope, check the waveform of the rear view monitor camera assembly.

HINT:

A waterproof connector is used for the rear view monitor camera assembly. Therefore, check the waveform at the radio and display receiver assembly with the connector connected.

OK:

The waveform is the same as that shown in the diagram.

Item

Content

Test probe

F131-28 (V+) - F129-1 (GND1)

Measurement setting

200 mV/DIV., 50 µs./DIV.

Condition

Ignition switch ON, shift lever in R

HINT:

  • The video waveform changes depending on the image sent by the rear view camera assembly.
  • The video waveform is output continuously when the ignition switch is in ON.

*a

Component with Wire Harness Connected

(Radio and Display Receiver Assembly)

*a

Waveform 1 (camera lens not covered, image displayed)

*b

Waveform 2 (camera lens covered, screen obstructed)

*c

Sync signal

*d

Video waveform

OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE REAR VIEW MONITOR CAMERA ASSEMBLY