Disassembly
DISASSEMBLY
PROCEDURE
1. DETACH FRONT AXLE SHAFT INBOARD JOINT BOOT CLAMP No. 2
(a) Secure the axle shaft in a vise between aluminum plates.
NOTICE:
Do not overtighten the vise.
(b) Using pliers, detach the front axle shaft inboard joint boot clamp No. 2. |
![]() |
2. DETACH FRONT AXLE SHAFT INBOARD JOINT BOOT CLAMP
(a) Detach the front axle shaft inboard joint boot clamp.
HINT:
Perform the same procedure as for the front axle shaft inboard joint boot clamp No. 2.
3. DETACH FRONT AXLE SHAFT INBOARD JOINT BOOT
(a) Detach the front axle shaft inboard joint boot from the front drive shaft inboard joint assembly.
4. REMOVE FRONT AXLE SHAFT INBOARD JOINT ASSEMBLY
(a) Remove the old grease from the front drive shaft inboard joint assembly.
(b) Make alignment marks on the front axle shaft inboard joint assembly and the front axle shaft outboard joint assembly. NOTICE: Do not make the alignment marks with a center punch. |
|
(c) Separate the front axle shaft inboard joint assembly from the front axle shaft outboard joint assembly.
NOTICE:
- Take care when separating the front drive shaft inboard joint assembly from the front drive shaft outboard joint assembly, as the tripod joint rollers may fall out.
- Do not drop the tripod joint rollers.
(d) Remove the 3 tripod joint rollers. |
![]() |
(e) Secure the axle shaft in a vise between aluminum plates.
NOTICE:
Do not overtighten the vise.
(f) Using snap ring pliers, remove the front drive shaft inboard shaft snap ring from the front drive shaft outboard joint assembly. |
![]() |
(g) Make alignment marks on the front axle shaft outboard joint assembly and the tripod joint. NOTICE: Do not make the alignment marks with a center punch. |
|
(h) Using a brass bar and a hammer, drive the tripod joint out of the front axle shaft outboard joint assembly.
NOTICE:
- Do not strike the surfaces where the rollers contact the tripod joint.
- Do not drop the tripod joint.
5. REMOVE FRONT AXLE SHAFT INBOARD JOINT BOOT
(a) Remove the front axle shaft inboard joint boot clamp No. 2, the front axle shaft inboard joint boot, and the front axle shaft inboard joint boot clamp.
6. REMOVE LH FRONT AXLE SHAFT DAMPER
(a) Using needle-nose pliers, detach the 2 front axle shaft damper clamps. |
![]() |
(b) Remove the front axle shaft damper and the 2 front axle shaft damper clamps from the front drive shaft outboard joint assembly.
7. DETACH FRONT AXLE SHAFT OUTBOARD JOINT BOOT CLAMP No. 2
(a) Using pliers, detach the front axle shaft outboard joint boot clamp No. 2, as shown in the illustration. |
![]() |
8. DETACH FRONT AXLE SHAFT OUTBOARD JOINT BOOT CLAMP
(a) Detach the front axle shaft outboard joint boot clamp.
HINT:
Perform the same procedure as for the front axle shaft outboard joint boot clamp No. 2.
9. REMOVE FRONT AXLE SHAFT OUTBOARD JOINT BOOT
(a) Remove the front axle shaft outboard joint boot clamp, the front axle shaft outboard joint boot, and the front axle shaft outboard joint boot clamp No. 2 from the front axle shaft outboard joint assembly.
(b) Remove the old grease from the outboard joint.
10. REMOVE LH FRONT AXLE SHAFT DUST DEFLECTOR
HINT:
Perform this procedure only if the LH front axle shaft dust deflector is deformed.
(a) Using the SST and a press, remove the LH front axle shaft dust deflector. SST: 09950-00020 NOTICE:
|
![]() |
11. REMOVE FRONT AXLE SHAFT RH DUST SEAL
(a) Using a press, remove the front axle shaft RH dust seal. NOTICE: Take care not to drop the front drive shaft inboard joint assembly. |
![]() |








