Drive Shaft

Reassembly

~8min read
3special tools

REASSEMBLY

PROCEDURE

1. INSTALL FRONT AXLE SHAFT LH DUST SEAL

(a) Using a metal plate and a press, install a new front axle shaft LH dust seal.

NOTICE:

  • The dust seal must be fully installed.
  • Take care not to damage the front axle shaft dust seal.
  • Install the front axle shaft LH dust seal sleeve facing the correct direction.

*a

Metal plate

2. INSTALL FRONT AXLE SHAFT RH DUST SEAL

(a) Using the SST and a press, install a new front axle shaft RH dust seal so that the distance (A) between the end of the center axle shaft and the front axle shaft RH dust seal is as specified.

SST: 09527-10011

Distance (A):

91.0 to 92.0 mm (3.59 to 3.62 in.)

NOTICE:

  • The front axle shaft RH dust seal must be fully installed.
  • Take care not to damage the front axle shaft RH dust seal.
  • Install the front axle shaft RH dust seal facing the correct direction.

3. INSTALL FRONT AXLE OUTBOARD JOINT BOOT

(a) Wrap protective tape around the splines of the front axle shaft outboard joint assembly to prevent damage to the boot.

*a

Protective tape

(b) Install the new parts onto the front axle shaft outboard joint assembly in the following order:

*1

Front axle shaft outboard joint assembly

*2

No. 2 front axle outboard joint boot clamp

*3

Front axle outboard joint boot

*4

Front axle outboard joint boot clamp

Outboard joint side

Inboard joint side

(1) No. 2 front axle outboard joint boot clamp

(2) Front axle outboard joint boot

(3) Front axle outboard joint boot clamp

(c) Apply grease to the sealed portion of the front axle shaft outboard joint assembly and the front axle outboard joint boot.

Standard grease quantity:

80 to 100 g (2.83 to 3.52 oz.)

(d) Install the front axle outboard joint boot into the groove of the front axle shaft outboard joint assembly.

NOTICE:

  • Do not allow grease to adhere to the front axle outboard joint boot clamp contact area.
  • Keep the inside of the front axle outboard joint boot free of foreign matter.

4. INSTALL NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP

(a) Secure the axle shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.

(b) Install the No. 2 front axle outboard joint boot clamp onto the front axle outboard joint boot.

(c) Position the SST on the No. 2 front axle outboard joint boot clamp, press it against the boot, and lightly tighten the SST.

SST: 09521-24010

*a

Hold

*b

Turn

(d) Tighten the SST so that the No. 2 front axle outboard joint boot clamp is crimped.

NOTICE:

Do not overtighten the SST.

(e) Remove the SST.

(f) Using the SST, measure the clearance of the No. 2 front axle outboard joint boot clamp.

SST: 09240-00020

Clearance:

1.2 to 4.0 mm (0.0473 to 0.157 in.)

If the clearance is outside the specified range, retighten the SST.

5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

(a) Install the front axle outboard joint boot clamp onto the front axle outboard joint boot.

(b) Position the SST on the front axle outboard joint boot clamp, press it against the boot, and lightly tighten the SST.

SST: 09521-24010

*a

Hold

*b

Turn

(c) Tighten the SST so that the front axle outboard joint boot clamp is crimped.

NOTICE:

Do not overtighten the SST.

(d) Remove the SST.

(e) Using the SST, measure the clearance of the front axle outboard joint boot clamp.

SST: 09240-00020

Clearance:

1.2 to 4.0 mm (0.0473 to 0.157 in.)

If the clearance is outside the specified range, retighten the SST.

6. INSTALL FRONT AXLE SHAFT LH DYNAMIC DAMPER

(a) Install the parts onto the front drive shaft outboard joint assembly in the following order, as shown in the illustration.

(1) New front axle shaft dynamic damper clamp

(2) Front axle shaft LH dynamic damper

(3) New front axle shaft dynamic damper clamp

*1

Front axle shaft outboard joint assembly

*2

Front axle shaft RH dynamic damper

*3

Front axle shaft dynamic damper clamp

(b) Adjust the dimension (A) as specified below.

Dimension (A):

229 to 233 mm (9.02 to 9.17 in.)

(c) Clamp the axle shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.

(d) Install the 2 front axle shaft dynamic damper clamps onto the front axle shaft LH dynamic damper.

NOTICE:

Be sure to install the clamp in the correct position.

(e) Using long-nose pliers, engage the 2 claws to install the 2 front drive shaft dynamic damper clamps, as shown in the illustration.

7. INSTALL FRONT AXLE SHAFT INBOARD JOINT ASSEMBLY

(a) Install the new parts onto the front axle shaft outboard joint assembly in the following order:

*1

Front axle inboard joint boot clamp

*2

Front axle inboard joint boot

*3

No. 2 front axle inboard joint boot clamp

*a

Protective tape

Outboard joint side

Inboard joint side

(1) Front axle inboard joint boot clamp

(2) Front axle inboard joint boot

(3) No. 2 front axle inboard joint boot clamp

(b) Clamp the axle shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.

(c) Remove the masking tape.

(d) Align the matchmarks and install the tripod joint onto the front axle shaft outboard joint assembly.

NOTICE:

Orient the splined portion of the tripod joint outward, and install it onto the end of the outboard joint.

*a

Alignment Mark

(e) Using a brass bar and a hammer, install the tripod joint onto the front axle shaft outboard joint assembly.

NOTICE:

  • Do not strike the surfaces where the rollers contact the tripod joint.
  • Keep the tripod joint free of foreign matter.
  • Be sure to install the tripod joint facing the correct direction.

(f) Using snap ring pliers, install a new snap ring onto the front axle shaft outboard joint assembly.

(g) Apply grease to the front axle inboard joint assembly and the front axle inboard boot.

Standard grease quantity:

195 to 215 g (6.88 to 7.58 oz.)

(h) Install the 3 rollers onto the tripod joint.

NOTICE:

  • Make sure to install the rollers in the correct direction, as shown in the illustration.
  • Do not drop the rollers.

(i) Align the alignment marks and install the front axle inner joint assembly onto the front axle shaft outer joint assembly.

*a

Alignment Mark

8. INSTALL FRONT AXLE INNER JOINT BOOT

(a) Install the front axle inner joint boot onto the front axle inner joint assembly.

(b) Check that dimension (A) of each axle shaft meets the specification.

Dimension (A):

Left side

590.5 mm (1.94 ft)

Right side

887.1 mm (2.91 ft)

*a

Left side

*b

Right side

9. INSTALL FRONT AXLE INNER JOINT BOOT CLAMP

(a) Secure the axle shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.

(b) Install the front axle inner joint boot clamp onto the front axle inner joint boot.

(c) Place the SST on the front axle inner joint boot clamp, press it against the boot and lightly tighten the SST.

SST: 09521-24010

(d) Tighten the SST so that the front axle inner joint boot clamp is crimped.

NOTICE:

Do not overtighten the SST.

(e) Remove the SST.

(f) Using the SST, measure the clearance of the front axle inner joint boot clamp.

SST: 09240-00020

Clearance:

1.2 to 4.0 mm (0.0473 to 0.157 in.)

If the clearance is outside the specified range, retighten the SST.

10. INSTALL FRONT AXLE INNER JOINT BOOT CLAMP NO. 2

(a) Install the front axle inner joint boot clamp No. 2 onto the front axle inner joint boot.

(b) Place the SST on the front axle inner joint boot clamp No. 2, press it against the boot and lightly tighten the SST.

SST: 09521-24010

(c) Tighten the SST so that the front axle inner joint boot clamp No. 2 is crimped.

NOTICE:

Do not overtighten the SST.

(d) Remove the SST.

(e) Using the SST, measure the clearance of the front axle inner joint boot clamp No. 2.

SST: 09240-00020

Clearance:

1.2 to 4.0 mm (0.0473 to 0.157 in.)

If the clearance is outside the specified range, retighten the SST.

11. INSPECT FRONT AXLE SHAFT ASSEMBLY

Click here