Exterior Panels / Trim

Removal

~4min read

REMOVAL

PRECAUTION / NOTICE / HINT

The procedures required (adjustment, calibration, initialization or registration), which must be performed once the parts have been removed and installed, or replaced when removing/installing the masking tape, are indicated below.

Procedure Required After Replacing / Removing / Installing Parts

Replaced Part or Performed Procedure

Required Procedure

Effect/Inoperative Function When Required Procedure Is Not Performed

Link

Disconnect the cable from the negative (-) battery terminal.

Initialize Back Door Lock

Door Lock Control System

Memorize Steering Angle Neutral Point

Lane Departure Alert System (with Steering Control)

Pre-Collision System

  • Rear Door Window Regulator Assembly
  • Rear Door Window Glass Subassembly
  • Rear Door Window Slider

Initialize Power Window Control System

  • Automatic Open and Close Function
  • Anti-Pinch Function
  • Anti-Pinch Function Operation
  • Remote Control Function
  • Key-Linked Function
  • Function Linked to Remote Control Transmitter
  • Keyless Operation
  • Power Window Open Warning Function

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. PRECAUTIONS

NOTICE:

After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

Click here

2. DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL

Click here

NOTICE:

When the cable has been disconnected, some systems must be reset after the cable is reconnected.

Click here

3. REMOVE THE REAR DOOR INSIDE HANDLE GARNISH CLIP

Click here

4. REMOVE THE REAR POWER WINDOW SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Click here

5. REMOVE THE REAR DOOR REAR FRAME BRACKET

Click here

6. REMOVE THE REAR DOOR TRIM PANEL SUB-ASSEMBLY

Click here

7. REMOVE THE REAR DOOR BELT REAR WEATHERSTRIP

Click here

8. REMOVE THE REAR DOOR GLASS INNER WEATHERSTRIP

Click here

9. REMOVE THE REAR DOOR BELT WEATHERSTRIP

Click here

10. REMOVE REAR DOOR ACCESS HOLE COVER

Click here

11. REMOVE REAR DOOR WEATHERSTRIP

Click here

12. REMOVE THE REAR DOOR GLASS LOWER REAR FRAME SUB-ASSEMBLY

Click here

13. REMOVE THE REAR DOOR GLASS SUB-ASSEMBLY

Click here

14. REMOVE THE REAR DOOR FRAME GARNISH

Click here

15. REMOVE THE REAR DOOR GLASS RUN

Click here

16. REMOVE THE REAR DOOR QUARTER GLASS

Click here

17. REMOVE REAR DOOR LOWER OUTER GARNISH MOLDING

HINT:

When removing the rear door lower outer garnish molding, heat the vehicle body and the rear door lower outer garnish molding using a heat light.

Heating Temperature

Item

Temperature

Rear Door Lower Outer Garnish Molding and Vehicle Body

40 à 60 °C

CAUTION:

  • Do not touch heated parts or the heat lamp. Touching them may cause burns.
  • Prolonged contact with heated parts may cause burns.

*a

Hot Surface

*b

Heat Lamp

NOTICE:

Do not overheat the vehicle body.

(a) Using a heat light, heat the rear door lower outer garnish molding and the vehicle body.

(b) Pull up one end of the rear door lower outer garnish molding to remove it.

HINT:

When pulling the rear door lower outer garnish molding, pull it parallel to the vehicle body.

18. REMOVE REAR DOOR OUTER GARNISH MOLDING

HINT:

When removing the rear door outer garnish molding, heat the vehicle body and the rear door outer garnish molding using a heat light.

Heating Temperature

Item

Temperature

Rear Door Outer Garnish Molding and Vehicle Body

40 à 60 °C

CAUTION:

  • Do not touch heated parts or the heat lamp. Touching them may cause burns.
  • Prolonged contact with heated parts may cause burns.

*a

Hot Surface

*b

Heat Lamp

NOTICE:

Do not overheat the vehicle body.

(a) Using a heat light, heat the rear door outer garnish molding and the vehicle body.

(b) Pull up one end of the rear door outer garnish molding to remove it.

HINT:

When pulling the rear door outer garnish molding, pull it parallel to the vehicle body.