Seats

Removal

~5min read

REMOVAL

PRECAUTION / NOTICE / HINT

The procedures required (adjustment, calibration, initialization or registration) that must be performed after parts have been removed, installed or replaced during front seat assembly removal/installation are indicated below.

Procedure Required After Replacing / Removing / Installing Parts

Replacement part or procedure

Necessary Procedures

Effects / Inoperative Function When Necessary Procedure Not Performed

Link

Disconnect the cable from the negative (-) battery terminal.

Initialize Back Door Lock

Door Lock Control System

Memorize Steering Angle Neutral Point

Lane Departure Alert System (with Steering Control)

Pre-Collision System

CAUTION:

  • Be sure to read the Precautions carefully before performing maintenance.

    Click here

  • Wear protective gloves. Sharp edges on parts may cause injury to your hands.

NOTICE:

If the front seat airbag assembly has deployed, replace the front seat airbag assembly, the front seat back frame sub-assembly, the separate-type front seat back pad and the separate-type front seat back cover with the necessary parts, depending on the damage caused by the collision.

HINT:

  • Perform the same procedure for the driver side and front passenger side.
  • The procedure below applies to the driver side.

PROCEDURE

1. PRECAUTIONS

NOTICE:

After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

Click here

2. DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL

Click here

CAUTION:

  • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  • If any Supplemental Restraint System (SRS) component is accidentally deployed, serious injury may result.

NOTICE:

When the cable has been disconnected, some systems must be reset after the cable is reconnected.

Click here

3. REMOVE FRONT SEAT HEADREST ASSEMBLY

(a) Remove the front seat headrest assembly from the front seat assembly.

4. REMOVE FRONT SEAT OUTER SLIDE SUPPORT COVER

(a) Operate the seat slide adjusting handle and move the front seat assembly as far rearward as possible.

(b) Release the claws to remove the front seat outer slide support cover.

5. REMOVE FRONT SEAT INNER SLIDE SUPPORT COVER

(a) Release the claws to remove the front seat inner slide support cover.

6. REMOVE SEAT OUTER SLIDE COVER

(a) Operate the seat slide adjusting handle and move the front seat assembly as far forward as possible.

(b) Release the claws and guide to remove the seat outer slide cover.

7. REMOVE SEAT INNER SLIDE SUPPORT COVER

(a) Release the claws and guide to remove the seat inner slide support cover.

8. REMOVE FRONT SEAT ASSEMBLY

(a) Using a TORX T50 socket, remove the 2 bolts on the rear part of the front seat assembly.

(b) Operate the seat slide adjusting handle and move the front seat assembly as far rearward as possible.

(c) Using a TORX T50 socket, remove the 2 bolts on the front part of the front seat assembly.

(d) Operate the seat slide adjusting handle and move the front seat assembly toward the center as far as possible.

(e) Operate the seat reclining adjuster release handle and move the seatback to the upright position.

(f) Disconnect the front seat airbag assembly connector under the front seat assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(1) Push the white housing lock and slide the yellow CPA. (At this stage, the connector cannot be disconnected.)

*a

White housing lock

*b

Yellow CPA

Slide

(2) Push the white housing lock again and disconnect the connector.

NOTICE:

Do not press the part (A) shown in the illustration when disconnecting the connector.

(g) Disconnect the front seat airbag assembly connector. (for front passenger side)

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(1) Slide the slider to release the lock, then disconnect the connector.

*a

Slider

-

-

Slide

-

-

(h) Disconnect each connector and release each clamp under the front seat assembly.

(i) Remove the front seat assembly as shown in the illustration.

NOTICE:

  • At least 2 persons are required when moving the front seat assembly out of the vehicle.
  • Protect the front seat foot.
  • Take care not to damage the front seat assembly, the body exterior or the body interior.