Installation
INSTALLATION
PRECAUTION / NOTICE / HINT
CAUTION:
- Be sure to read the Precautions carefully before performing maintenance.
Click here
.gif)
- Wear protective gloves. Sharp edges on parts may cause injury to your hands.
HINT:
- Perform the same procedure for the driver side and front passenger side.
- The procedure below applies to the driver side.
PROCEDURE
1. INSTALL FRONT SEAT ASSEMBLY
(a) Place the front seat assembly in the vehicle as shown in the illustration. NOTICE:
|
![]() |
(b) Connect the front seat airbag assembly connector under the front seat assembly.
(1) Before connecting the connector, make sure the housing lock position is correct, as shown in the illustration.
*a |
Correct |
*b |
Incorrect |
*c |
Yellow CPA |
- |
- |
(2) Engage the connectors until they lock (when locking, make sure a click is heard).
NOTICE:
- When connecting any airbag connector, take care not to damage the airbag wire harness.
- While engaging, the white housing lock will slide. Do not hold the white housing lock or the upper part of the yellow CPA, as this may cause improper fitting.
(c) Connect the front seat cushion airbag assembly connector. (for front passenger side)
(d) Connect each connector and engage each clamp under the front seat assembly.
(e) Temporarily install the front seat assembly with the 4 bolts.
(f) Operate the seat slide adjusting handle and move the front seat assembly as far rearward as possible.
(g) Using a TORX T50 socket, tighten the 2 bolts on the front part of the front seat assembly. Torque: 37 N·m {377 kgf·cm, 27 ft·lbf} NOTICE: Tighten the bolts in the order shown in the illustration. |
![]() |
(h) Operate the seat slide adjusting handle and move the front seat assembly as far forward as possible.
(i) Using a TORX T50 socket, tighten the 2 bolts on the rear of the front seat assembly. Torque: 37 N·m {377 kgf·cm, 27 ft·lbf} NOTICE: Tighten the bolts in the order shown in the illustration. |
![]() |
2. INSPECT SEAT SLIDE ADJUSTER LOCKING
(a) When the front seat assembly slides, check that the left and right adjusters move smoothly together and lock simultaneously. If the seat adjusters do not lock simultaneously, loosen the front seat assembly mounting bolts and adjust the position of the adjuster.
3. INSTALL SEAT SLIDE SUPPORT INNER COVER
(a) Operate the seat slide adjusting handle and move the front seat assembly as far forward as possible.
(b) Engage the claws and guide to install the seat slide support inner cover. |
![]() |
4. INSTALL SEAT SLIDE OUTER COVER
(a) Engage the claws and guide to install the seat slide outer cover. |
![]() |
5. INSTALL FRONT SEAT SLIDE SUPPORT INNER COVER
(a) Operate the seat slide adjusting handle and move the front seat assembly as far rearward as possible.
(b) Engage the claws to install the front seat slide support inner cover. |
![]() |
6. INSTALL FRONT SEAT SLIDE SUPPORT OUTER COVER
(a) Engage the claws to install the front seat slide support outer cover. |
![]() |
7. INSTALL FRONT SEAT HEADREST ASSEMBLY
(a) Install the front seat headrest assembly onto the front seat assembly.
8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Click here![]()
NOTICE:
When the cable has been disconnected, some systems must be reset after the cable is reconnected.
Click here
![]()
9. INSPECT SEAT HEATERS (with seat heater system)
Click here![]()
10. PERFORM DIAGNOSTIC SYSTEM CHECK
Click here![]()
11. INSPECT SRS WARNING LIGHT
Click here![]()



.png)
.png)
.png)
.png)