Door Lock

Removal

~5min read

REMOVAL

PRECAUTION / NOTICE / HINT

The procedures necessary (adjustment, calibration, initialization or registration) that must be performed after parts have been removed, installed or replaced during rear door lock assembly with motor removal/installation are shown below.

Procedure Required After Replacing / Removing / Installing Parts

Replaced Part or Performed Procedure

Required Procedure

Effect/Inoperative function when procedure not performed

Link

Disconnect the cable from the negative (-) battery terminal.

Initialize Back Door Lock

Door Lock Control System

Memorize Steering Angle Neutral Point

Lane Departure Alert System (with Steering Control)

Pre-Collision System

  • Rear Door Window Glass Subassembly
  • Rear Door Window Slider

Initialize Power Window Control System

  • Automatic Open and Close Function
  • Anti-Pinch Function
  • Anti-Pinch Function Operation
  • Remote Control Function
  • Key-Linked Function
  • Function Linked to Remote Control Transmitter
  • Keyless Operation
  • Power Window Open Warning Function

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. PRECAUTIONS

NOTICE:

After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

Click here

2. DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL

Click here

NOTICE:

When the cable has been disconnected, some systems must be reset after the cable is reconnected.

Click here

3. REMOVE REAR DOOR REAR FRAME BRACKET

Click here

4. REMOVE REAR DOOR INSIDE HANDLE GARNISH CLIP

Click here

5. REMOVE REAR POWER WINDOW SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Click here

6. REMOVE THE REAR DOOR TRIM PANEL SUB-ASSEMBLY

Click here

7. REMOVE REAR DOOR TRIM BRACKET

Click here

8. REMOVE REAR DOOR SERVICE HOLE COVER

Click here

9. REMOVE REAR DOOR OUTSIDE HANDLE COVER

Click here

10. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

Click here

11. REMOVE REAR DOOR LOCK ASSEMBLY WITH MOTOR

(a) Disconnect the connector.

(b) Using a "TORX" T30 socket wrench, remove the 3 screws and the rear door lock assembly with motor.

(c) If reusing the rear door lock assembly with motor:

(1) Remove the door lock wire harness gasket from the rear door lock assembly with motor.

12. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

(a) without Double Lock System:

(1) Using a screwdriver with its tip wrapped in protective tape, release the claw as shown in the illustration.

*a

Protective tape

Remove in this direction

(2) Release the guide to remove the rear door lock remote control cable assembly from the rear door lock assembly with motor.

(b) with Double Lock System:

(1) Using a screwdriver with its tip wrapped in protective tape, release the claw as shown in the illustration.

*a

Protective tape

Remove in this direction

(2) Release the guide to remove the rear door lock remote control cable assembly from the rear door lock assembly with motor.

13. REMOVE REAR DOOR INSIDE LOCK CABLE ASSEMBLY

(a) without Double Lock System:

(1) Using a screwdriver with its tip wrapped in protective tape, release the claws as shown in the illustration.

*a

Protective tape

Remove in this direction

(2) Release the guide to remove the rear door inside lock cable assembly from the rear door lock assembly with motor.

(b) with Double Lock System:

(1) Using a screwdriver with its tip wrapped in protective tape, release the claws as shown in the illustration.

*a

Protective tape

Remove in this direction

(2) Release the guide to remove the rear door inside lock cable assembly from the rear door lock assembly with motor.

14. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY NO. 1

(a) Using a screwdriver with its tip wrapped in protective tape, release the claws as shown in the illustration.

*a

Protective tape

Remove in this direction

(b) Release the guide to remove the rear door lock remote control cable assembly No. 1 from the rear door lock assembly with motor.